Other heating and cooling equipment

Capacity: 1 m³ - 13 m³

CONDENSATE TANK “GENERAL INFORMATION AND MATERIAL QUALITY • Our company is controlled and audited by EKOTEK, Brand registered and ISO 9001:2015 quality management system. • Welding processes are carried out by certified welders in ...

Fresh air heat recovery unit Related introduction Heat recovery ventilator can help make mechanical ventilation more cost effective by reclaiming energy from exhaust airflows. With heat exchangers to heat or cool incoming fresh air, ...

Power: 1 kW - 4 kW
Temperature: 300 °C

JH-NR-13A High power high Quality garage heater far infrared heater for home and outdoor Input Power: 1.0~4.0kW Surface temperature ： 300℃ Cover Area： 20M2 Voltage: 220V~ Accessory: installing bracket, thermostat without remote Specification: ...

Xi'an Refra Tungsten & Molybdenum Co.,Ltd is one of the best China heater manufacturers and suppliers, and as a professional company we have ou own productive heater factorywelcome to wholesale products from us. As heat source of ...

Heat recovery units with an enthalpy exchanger is intended for ventilation systems as a modern element enabling the recovery of energy – heat and moisture. It is designed for ventilation of residential buildings: single- and multi-family ...

Reuse heat that is released during your storage Adjust your (cooling) system Use heat for heating Save energy General When you are cooling in one place, heat is released in another place. Usually this heat is dissipated to the ...

Air preheater (APH) is widely used in the production process of carbon black, and it is one of the most important production equipment. At the same time, APHs have also been promoted to other industries. At present, they have gradually ...

SAVANA INOX EC is corrosion resistant due to its specially modified water exchanger and stainless steel jacket. It will not succumb to an aggressive environment either. It also has efficient and energy-saving EC motors. It can be purchased ...

The preparation vessels are designed and manufactured in compliance with the strictest cGMP guidelines both for sterile and non-sterile productions. Size range from 2 up to 50.000 liters matching EU cGMP & FDA requirements as well ...

For steam applications Captures waste heat from blowdown process Maintains desired level of total dissolved solids (TDS) Up to 22 gpm blowdown water Up to 180 gpm makeup water Continuous boiler surface blowdown heat recovery (BDHR) ...

Here you can find kinds of band heaters for different applications. Nozzle band heaters for the nozzles of injection molding machines. Mineral insulated band heaters at high temperatures with high voltages. Mica band heaters for plastic ...

Power: 2.4 kW
Steam production: 0 kg/h
Pressure: 5 bar

PROFESSIONAL STEAM GENERATORS Thanks to the automatic charge it is possible to use FORZA 5 without limits, there will be no more waste of time. The cold water tank allows the boiler to be charged once the level drill crouches down, ...

Power: 300 W

Thermocups and cup heaters are designed for controlling the temperature of a mud sample while taking readings with a rheometer or viscometer. Normal heat-up time is 30 minutes and the pilot light turns on when the well reaches the set ...

Complete solar heating system with solar thermal water tank, solar collector, controller box, pump etc. - - Quality Non-pressure solar thermal collector 1)high efficiency solar collector 2)Polyurethane insulation 3)CE certified ...

Power: 10 kW - 84 kW

Gas heaters designed for indoor installation, available in three models with heating capacity from 9.4 to 75.6 kW. Thanks to a wide range of products (the heater is available in 14 models), it can be adjusted in terms of power, size ...

Capacity: 7,000 gal

The challenge presented by the customer was to dip a honeycomb composite block weighing as much as 3000 lbs into a tank of resin and then remove any excess resin. Davron met this challenge by designing a two chamber system. In the first ...

AUGUST Air Compressor can be optionally equipped with a Heat Recovery System.Also existing installations can be later updated by using the AUGUST heat recovery system. Why to use heat recovery? The answer is quite simple:While 94% ...

Howden was the first company to form a joint venture with Fredrik Ljungström. Since then, we have been designing and improving rotary heat exchanger technology through continual research, development and analysis of both new and aftermarket ...

Steam production: 500 kg/h - 1,800 kg/h

The new generation of a proven series. The CERTUSS Universal 500 - 1800 TC steam generators are characterized by the immediate modulating output adjustment and the simplified operation. TC is the abbreviation for Touch Control. CERTUSS ...

We provide Band Heaters for our customers, which we make in accordance with international quality standards utilizing high-quality raw materials. To assure trouble-free operation, these are sturdy and equipped with nickel chrome-resistant ...

We strongly believe that security can blend in naturally in our homes and that Maus is the natural security.product you need. You don't have to compromise on location or style. Let MAUS be the versatile solution for your home, your ...

ohmmat is a flexible heating mat made of high-performance silicone rubber. Our product has outstanding heating performances far beyond similar products in the market. ohmmat belongs to the ohmvo product family for heating or maintaining ...

Power: 35 kW - 3,488 kW
Steam production: 50 kg/h - 5,000 kg/h
Pressure: 6, 8, 10, 12 bar

- Wenta Steam Generator is manufactured and equipped with the latest technology. - It produces steam in a very fast and economical way. Thanks to its full automation control, it is extremely easy to use. (Controlled by PLC control.) - ...

Smooth and efficient energy transfer is the key factor of our Pre-Heater. The CT 36 is equipped with: 1. - Two heating rollers, which provide the required heat energy. 2. - A pneumatic pinion and dancer rollers, who create an optimum ...

Capacity: 500 l - 20,000 l

The series of equipment have the functions of heating, cooling, heat preservation and mixing preparation. The vessel carries out design and processing according to "Technical condition for steel made pressure vessel". The specifications ...