Amplifiers

Voltage: 0 V - 10 V
Current: 4 mA - 20 mA

Features ※ Micro structure(38*20*14mm) ※ Standard signal output,used for industry control

Voltage: 0 V - 1,000 V
Current: 7 A
Power: 7,000 W

... generates an output voltage up to 1000 V and an output current of 7 A. The switching amplifier RCV 1000/7 operates as an amplifier with energy recovery. This amplifier principle is ...

... radiation is generated by a pulsable CO2 laser system developed by TRUMPF – the TRUMPF Laser Amplifier. From just a few watts to 40 kilowatts The TRUMPF Laser Amplifier sequentially intensifies a ...

Voltage: 10 V
Current: 4 mA

The TSVA2-DGM is a 2-channel vibration amplifier that is used in connection with our broad bandsensor BV100 A Montronix SPECTRA™ controls the TSVA2-DGM via an RS485 interface. This enables you to set individual ...

Power: 1 W

DT-730: DVB-T 30 dBm Power amplifier (1 W) The DT-730 is a high quality 1 W RF power amplifier for COFDM signals, both for single carrier or multicarrier system. The system provides an amplified output ...

For some applications, the ±10V that’s standard among almost all analog output cards just won’t do the trick; they need voltage levels as much as ten times that amount. For that purpose, UEI has developed the PD-AOAMP-115, a 16-channel ...

Frequency: 0 Hz - 10,000 Hz

Features: * Indicator for voltage and current output * Indicator for output signal * Output current can be adjusted from 2A to 10A * Hot protect for output transistor * Indicator for output transistor invalidation * Constant current ...

Features: Designed with the latest and most advanced peltier-based semiconductor technology; Fine tuning hot lid, suitable to various consumptive materials; Large 5.7’’ high-definition LCD display, real-time display process by ...

Frequency: 0.05 MHz - 500 MHz

The AP-0.5GZ23 amplifier is a low-noise, wide bandwidth amplifier that can be used with the RFC-101 series RF Current Probes. 2.0 Key Features • High gain and low noise • Wide bandwidth • Standard ...

Voltage: 24 V
Current: 4 mA - 20 mA

AMPLI-Block is a load cell/transducer amplifier. AMPLI-Block offers many benefits in a compact design such as very easy set up and two outputs (one with adjustable filter). AMPLI-Block may be used with one or two load ...

Voltage: 12 V - 24 V
Current: 100, 50 mA
Frequency: 10 Hz - 55 Hz

Control output The load voltage is below 24V DC, and the load current is below 100mA. NPN open set electric output type (nesidual voltage below 1V) When light in ON /when light out ON, switching mode Automatic on time opération ...

Voltage: 0 V - 10 V
Current: 4 mA - 20 mA

Board which is designed to amplify a signal to equipment with current loop 4-20mA or 0-10V. For 35mm DIN rail. Features: Range of operation temperature Min:-10ºC / Max: +40ºC. Power supply: 24VDC. Range of input signal: 0 – 30 mV. Output ...

Voltage: 110 V - 200 V
Frequency: 0 Hz - 20,000 Hz

All DynaLabs vibration shakers come included with an amplifier out of the box. PM-20, PM-100, MS-20 and MS-100 shakers have integrated amplifiers. With this integrated amplifier it ...

Voltage: 100 V - 1,200 V
Frequency: 2 Hz - 20,000 Hz

• Designed with state-of-the-art MOSFET transistors • Sine output power up to 1200 VA • Selectable operation in current or voltage mode • Backgroundlit multifunctional display • Safety management system monitors temperature, overcurrent, ...

Voltage: 9 V - 16.6 V
Power: 4 W
Frequency: 1,985 MHz - 2,070 MHz

PIDSO‘s high efficiency linear power amplifier CRD.002-00A is ideally suited for rugged COFDM Video transmission applications in high PAPR scenarios. The high-efficiency linear power amplifier is built ...

Loop inductance amplifier; Single channel; DIN rail connection; loop inductance range 20uH-1000uH; adjustable sensitivity 0.01%-1%; Automatic Sensitivity Boost; Manual and Automatic Frequency Tuning; 4 adjustable loop ...

Voltage: 25 V - 70.7 V
Power: 50 W - 100 W

The ECC-50BDA is an intelligent amplifier that can be configured for 50 watts or 100 watts of total audio power. It is used with the ECC-50/100(E) emergency voice evacuation system to amplify an audio message for distribution ...

Voltage: 250 V
Current: 1 A

... Contacts isolated from each other Galvanic Isolation Simple USB Configuration Port The SEM1630 is a DIN rail mounted trip amplifier which accepts RTD, Thermocouple, mV and passive current signals and provides a dual ...

The PIB24L165 is a scalable driver board which, for an input of 0 to 10V (or 0 to 20mA), generates a proportional output current of 0 to 165mA. By shorting out jumper JP1 (shorting header not supplied), the control will be changed from ...

... output, meeting the requirements of dual energy range experimental setups, avoiding the split of the signal on two shaping amplifiers.

Voltage: 24 V
Current: 4 A
Frequency: 50, 60 Hz

... window range Integral/Window mode The ORTEC Model 590A Amplifier and Timing Single-Channel Analyzer includes both a low-noise shaping amplifier and a timing single-channel analyzer. The amplifier ...

Voltage: 12 V
Power: 100, 150, 200 W

... Air Horn.The amplifier circuit use the highly effective magnetic core transformer and is resistance to interference, stable and reliable inworking ■ Nova® Siren Amplifier Product Introduction The ...

Maxphotonics 5W, 20W polarization-maintaining amplifier has the features of high output polarization extinction ratio and strong stability power. The Output polarization extinction ratio is16dB or more, high power stability, ...

Power: 6 W
Frequency: 2 MHz

Laser light with variable wavelengths are available via optical parametric amplifiers. The AVUS Optical Parametric Amplifier (OPA) provides widely tunable high-energy pulses. It is ideal for use with ...