Automatic presses

Force: 70 tf
Stroke: 500 mm
Working speed: 5 mm/s

The KP-A series consists of powerful hydraulic presses with portal frames, which are built completely in Europe using high-quality components from reputable suppliers and used for deep drawing, forming, and notching processes. The possible ...

Force: 100 tf
Stroke: 500 mm
Working speed: 4 mm/s

The KP-A series consists of powerful hydraulic presses with portal frames, which are built completely in Europe using high-quality components from reputable suppliers and used for deep drawing, forming, and notching processes. The possible ...

Force: 150 tf
Stroke: 500 mm
Hydraulic pump power: 4 kW

The KP-A series consists of powerful hydraulic presses with portal frames, which are built completely in Europe using high-quality components from reputable suppliers and used for deep drawing, forming, and notching processes. The possible ...

Force: 350 kN - 2,500 kN
Opening: 200 mm - 540 mm
Stroke: 70 mm - 300 mm

... is easy to see that AIDA NC presses are an industry standard. PRESS FEATURES Highly rigid frame to minimize deflection Ball and Socket Connections Hydraulic Overload Protection System (HOLP) AIDA ...

Force: 2,000, 1,600, 1,100, 3,000, 2,500 kN
Opening: 350 mm - 450 mm
Stroke: 110 mm - 300 mm

... acting HOLP system (10 msec) AIDA Wet clutch and Brake 6-Point full length Bronze Gibs Brake stop-time monitoring display Automatic lubrication system for Gibs and Crankshaft Bearings AIDA MPC safety controller Quill ...

Force: 20,000 kN
Working speed: 0 mm/s

Specific pressure 500 kg/cm² Dimensions of heater plates: 1500 x 1500 mm Implementation examples: We supplied to a Korean manufacturer of large television screens a machine with platens of 2,800 mm x 1,600 mm for which we obtained ...

Force: 1,500 kN

Closing from the top Specific pressure 600 kg/cm² Safety: light curtain, dual-hand control Available as single-deck or double-deck machine Implementation examples: dielectric resonator

Force: 5,000 kN

Closing from the top Specific pressure 2600 kg/cm² Bottom ejection battery Implementation examples: brake pads, clutch disks, powder metal parts

Force: 0 kN - 10,000 kN

... IR oven Automatic high speed transfer device and automatic tool change system PLC for temperature monitoring To process PPS, PEI or PEEK, our compact unit performs short and repetitive cycles, ...

Force: 10,000 kN
Table width: 3,000 mm
Table length: 2,000 mm

... including the ECS PRESS system - fully equipped, allowing to obtain all industrial developments needed to drive structural composite materials towards industrialization. Discover more about the fast RTM platform. FULLY AUTOMATED ...

Force: 0 kN - 25,000 kN

... supplier of large scale hydraulic press systems and production lines, offer its customers a complete range of polymerization press equipment. CURING PRESS FOR COMPOSITE APPLICATIONS Pinette ...

The press MECAMAQ type PHH-300, It has been designed specially for the suitable one or shaped of profiles for companies of structures. It has a power of 300 Tm, with 1 cylinder of double effect, with course of 300 mm ...

Force: 1,765.2 kN
Opening: 850 mm
Stroke: 400 mm

... guided by means of 2 cylindrical columns Ø40 with bronze sleeves. Hydraulic group with 2 speeds, approximation and work with automatic speed change by pressure or position. Approximation speed: 10 mm/sec. Engine power ...

Opening: 600 mm
Stroke: 300 mm
Max. pressure: 315 bar

... courses is by means of ends of stops and that of pressure for electrical switch with automatic investment. Operation by means of console to two hands and protection by photoelectric barriers. Features Power ...

Force: 46 kN
Max. pressure: 600 bar
Weight: 220 kg

400 mm overhang . When it comes to punching without pre-drilling, no other device can hold a candle to our AP 400 – no matter if you need to work on control cabinet housings, switch cabinet doors or mounting plates. Openings in round, ...

Force: 60 kN
Max. pressure: 165 bar

the strongest among our stationary punches is used when size matters. The numbers speak a clear language. 600 mm ovrehang, 66 mm punching stroke and 360 kg dead weight. This high-performance device was developed especially for control ...

Force: 46 kN
Max. pressure: 600 bar

The AP 250 for punching without pre-drilling. When the tasks are getting bigger, the devices from our AP line show their full potential. For example, for quick and easy punching of round, square, rectangular or special shapes in control ...

Force: 150 tf - 3,000 tf

The Faccin PPM+MA series is a remarkable range of hydraulic dishing presses with automatic manipulators, providing unmatched durability, reliability, and efficiency at a cost-effective price. It’s designed to meet the ...

Force: 10, 50 kN
Stroke: 50 mm
Table width: 255 mm

... , deforming, etc. They are designed for use not only as stand-alone presses but also integrated in automatic workstations, special machines or automated lines. AGME has two mini hydraulic presses models: ...

Force: 15, 30 kN
Stroke: 0 mm - 40 mm

To meet with more particular production processes, a range of pneumatic presses are specially suitable for crimping, riveting, bending, marking, blanking, punching and raising, with maximum precision and safety. Several types of controls ...

Force: 100, 36, 3, 15 kN
Opening: 200, 125, 75, 175 mm

aiPRESS servo presses are used to produce safe and reproduceable joinings. They offer optimal possibilities in customising the joining process to your needs. Process factors such as feed force, running speed, positioning time and accuracy ...

Force: 220 kN - 2,200 kN
Hydraulic pump power: 18.5 kW
Overall height: 600 mm

The “2200 NC+ hydraulic horizontal press can be relied upon to carry out all bending and straightening tasks in heavy steel construction, vehicle construction and steel service centres. The straightening and bending ...

Force: 220 kN - 2,200 kN
Hydraulic pump power: 18.5 kW
Overall height: 600 mm

... pre-tensioning) as additional services. The robust, heavy design of this bending press guarantees precise bending results. The special feature of this horizontal bending press lies in the use of a ...

Force: 220 kN - 2,200 kN
Hydraulic pump power: 30 kW
Overall height: 850 mm

... pre-tensioning) as additional services. The robust, heavy design of this bending press guarantees precise bending results. The special feature of this horizontal bending press lies in the use of a ...

Force: 50 kN
Stroke: 250 mm
Table width: 450, 300 mm

... (∅ 50 mm). We produce this 50 ton C frame press with a selector for manual / semi-automatic / automatic work-mode, two speeds, a pressure switch and light guards in the frontal working ...

Force: 100 tf
Stroke: 250 mm
Table width: 400, 550 mm

... (∅ 50 mm). We produce this 100 ton C frame press with a selector for manual / semi-automatic / automatic work-mode, two speeds, a pressure switch and light guards in the frontal working ...

Force: 300 kN
Stroke: 450 mm
Table width: 1,000 mm

... column press is manufactured with 4 cylindrical columns to ensure a perfect parallelism of the upper table. We recommend this type of hydraulic press when you have work that requires a high accuracy ...

Force: 4.2 kN
Opening: 90 mm - 1,020 mm
Stroke: 50 mm - 300 mm

... assembly in the press force range from 1.6 to 43 kN. In combination with the SCHMIDT® PressControl 75 or 700 control system, the presses become EC type-tested, CE-conform workstations, optionally with process monitoring. The ...

Force: 250, 200 kN
Stroke: 350 mm

... controllers developed for this purpose. These meet the most complex requirements, in single workstations as well as in fully automated production lines. The full-load modules of the SCHMIDT® ServoPress series are EC ...

Force: 5, 3 kN
Stroke: 200 mm

... controllers developed for this purpose. These meet the most complex requirements, in single workstations as well as in fully automated production lines. The full-load modules of the SCHMIDT® ServoPress series are EC ...

Force: 500 kgf
Opening: 42 mm - 185 mm
Stroke: 50 mm

... other types of manual press - rack and pinion manual presses and high-capacity rack and pinion manual presses - they make up the extensive range of EMG manual presses. Features : Ground and rotationally locked slide Automatic ...

Force: 700 kgf
Opening: 35 mm - 260 mm
Stroke: 40 mm

... other types of manual press - rack and pinion manual presses and high-capacity rack and pinion manual presses - they make up the extensive range of EMG manual presses. Features : Ground and rotationally locked slide Automatic ...

Force: 1,500 kgf
Opening: 60 mm - 250 mm
Stroke: 60, 30 mm

... adjusted slider locked for rotation - Automatic raising of the slider by spring - Quick and reliable adjustment of the clear height - Mechanical stop ensuring repetiveness of the cycle - Base support and press ...

Force: 300, 50 kN

Specifications: Stroke rate: continuously variable from 5 to max. 700 1/min. Press: nominal stamping capacity 300 kN, stroke 10 mm Slide units: max. nominal forming capacity 50 kN, max. stroke 10 mm Feed length: ...

Force: 150, 70, 100, 40 tf
Stroke: 500 mm
Table width: 900, 1,500, 1,050 mm

Hydraulic press suitable for straightening sheet metal, assembling and dismantling electric motors and more generally for any assembly operation. The PBM hydraulic workshop press is equipped with a ...

Force: 40 tf - 300 tf
Stroke: 500 mm
Table width: 700, 800, 900, 1,000, 1,200 mm

... with T-slots. The PCL electro-hydraulic press is supplied in models starting from 40 tons up to 300 tons and is available both in the semi-automatic version and with automatic operation. Semi-automatic ...

Force: 100 tf
Opening: 500 mm
Stroke: 500 mm

... the pressure. The PST electro-hydraulic press is supplied in models starting from 40 tons up to 400 tons and is available both in the semi-automatic version and with automatic operation. Semi-automatic ...

Force: 400 tf - 2,000 tf

The forging trimming press is mainly used for the metal hot-cut edge-cutting process. Perform flash-cutting processing on the hot blank forged by die forging. Also known as die forging trimming press. ...

Force: 200 tf

Zhengxi 200T SMC molding press, also called hydraulic compression molding press, is applied in making sheet moulding compound products. Our SMC hydraulic press machine has superior quality ...

Force: 160 tf - 3,000 tf

... calibration, mold calibration is more accurate and suitable for various molding conditions. Description A heated platen press is a kind of composite material molding equipment and also the main molding equipment for ...

Force: 294.2 kN - 2,451.7 kN
Opening: 1,050 mm

These presses are generally found in the workshops of every business; It is one of the basic machines used for all kinds of works such as compression, bending, driving, bearing removal, straightening, etc. Our manufacturing is user-oriented ...

Force: 30 tf - 400 tf
Stroke: 400 mm
Table width: 350 mm - 720 mm

These presses, which are preferred in all kinds of basic pressing operations with their robust and durable structure, three-gradual speed system and modular structure, are produced between 30 tons and 400 tons. Our manufacturing is user-oriented, ...

Force: 30 tf - 250 tf
Opening: 600 mm - 800 mm
Rate (strokes/min): 600 p/min

HCT model, which is frequently preferred in single-action pressing processes, allows the workpiece to be easily assembled/disassembled and observed during the operation process, as its three sides are open. At the same time, the most ...

Force: 0 kN - 2,000 kN
Opening: 200 mm - 1,900 mm

... Considerable Clamping Force • - Outstanding Precision • - Good Ergonomics • - Parallelism Measuring Function Why Die Spotting Press • - It allows you to conveniently match all the parts of the mould in more comfortable ...

Force: 0 N - 1,200 N
Opening: 170 mm - 1,470 mm

... of configuration ensures the excellent performance of press, and all the main components for mechanical processing are manufactured by imported machining center, to ensure machining precision of press ...

Force: 0 kN - 3,200 kN
Opening: 130 mm - 2,230 mm

... main components for mechanical processing are manufactured by imported machining center, to ensure machining precision of press elements. The shift-out rail of lower mold plate adopts wear resistant rail with intensified ...

Force: 50 tf

MSE Furnace is produced atmosphere controlled automatic hot press in accordance with the new requirements in the field of industry, Research and Development. Atmosphere controlled automatic ...

... / atmosphere controlled hot press with various features in accordance with the new requirements and the purpose of the process in technology, industry and R&D apart from the standard features. Automatic ...

... are capable of operating at pressures up to 700 MPa. With controlled pressurization and decompression (either manual or automatic), products with uniform density and reduced internal stresses can be produced. Common ...

Force: 981 kN
Table width: 996 mm
Table length: 1,740 mm

... operate the press electrically or manually (with the hand pump). In addition, the PTP 100 is equipped with an integrated manometer and pressure regulator. With these functions you can check the current pressure while ...

Force: 1,570 kN
Table width: 996 mm
Table length: 1,740 mm

... straightening press is equipped with an integrated manometer and pressure regulator. With these features you can check and control the current pressure during the operation of the press. The two-speed ...

Force: 200, 100, 150 kN

... that can be adjusted throughout the cycle. The press can be used alone, also communicating with other devices on the line via common data bus systems. in this way it is possible to control more than one press ...

Force: 100, 30, 60 kN

... that can be adjusted throughout the cycle. The press can be used alone, also communicating with other devices on the line via common data bus systems. in this way it is possible to control more than one press ...

Force: 300, 500, 600, 800 tf
Opening: 1,000, 1,200, 700 mm
Stroke: 400, 700 mm

... negative pressure in the oil system greatly reduces the failure rate, prolong the service life of the machine, electrical fault automatic alarm and a key reset function. 4, stable and durable: the frame adopts the whole ...

Force: 650, 1,200, 1,000, 800 tf
Stroke: 500 mm
Table width: 1,300, 1,200, 1,000 mm

1. Adopt servo motor imported from Italy, hydraulic control system from Japan, intelligent, stable operation and energy saving; 2. Pressure, stroke, pressure preservation can be adjusted according to the pressing process requirements, ...

Force: 1,000, 800, 3,000, 2,000, 1,500 kN
Table width: 600 mm
Table length: 550 mm

... requirements. 5. Safety: The machine is equipped with protective cover, LED working light and infrared ray, etc., multiple protection is safer. Scope of application: 1. Electrical appliances, lighting, key body ...