Dongguan Koves Cutting Tool Co., Ltd.
Material Stainless Steel - SS201,SS301, SS303, SS304, SS316, SS416 etc. - Steel - mild steel, Carbon steel, 4140, 4340, Q235, Q345B, 20#, 45# etc. - Brass - HPb63, HPb62, HPb61, HPb59, H59, H62, H68, H80 etc. ...
Clamping range: 38.13, 39.7, 77.8, 95.25 mm
Sunnen's basic honing machines can be found in thousands of tool rooms throughout the world. Machines in this category are well suited to the low volume production that is typically performed in tool rooms and repair departments. Sunnen ...
Sunnen Products Company
Clamping range: 50.8 mm - 117.48 mm
Sunnen's basic honing machines can be found in thousands of tool rooms throughout the world. Machines in this category are well suited to the low volume production that is typically performed in tool rooms and repair departments. Sunnen ...
Sunnen Products Company
Sunnen's basic honing machines can be found in thousands of tool rooms throughout the world. Machines in this category are well suited to the low volume production that is typically performed in tool rooms and repair departments. Sunnen ...
Sunnen Products Company
... heavy duty Pin Driving Chucks designed to be used in SPIROL’s Manual Pin Inserters (Model PM, Model PMH or Model PMX). A Pin Driving Chuck may also be used in a drill press or arbor press with an adaptor. ...
Remote actuator mounting can be achieved using valve extension spindles or pedestal adaptors. Lengths can be from 500 mm to 8 metres, (20" to 300") in stainless steel or carbon steel. • Underground applications • Customer specified ...
Clamping range: 40 mm - 63 mm
Walter Tools
Clamping range: 32 mm - 63 mm
Walter Tools
– High productivity and surface quality thanks to low-vibration bore machining – Time saving thanks to quick, precise tool changes (±0.002 mm) with QuadFit exchangeable heads – Reliable due to excellent chip removal from the bore thanks ...
Walter Tools
Clamping range: 0.5 mm - 13 mm
Feature – Ideal for gripping round rod-type samples – Secures sample tightly with firm gripping – Suitable for tensile and compression test
Clamping range: 10 mm - 200 mm
Tool holders are adapters used to mount cutting tools in the machine tool equipment that performs these operations. Ultrasonic tool holders generate vibrations along the tool axis, a movement that reduces the effects of friction and ...
Clamping range: 1.89, 444 in
... firmly lock or release workpiece. • Rugged Construction...But Slim Design weighing only about half as much as a standard chuck. This feature provides minimal reduction in positioner capacity. Also Available From ...
Fe Powertools tapping equipment. A special selection of top quality tap chucks and holders to fit in your magnetic drilling machines. Tap chucks FEQTE 001, 002 and 003 can be used in your FE 100 R/L mag ...
FE POWERTOOLS BV
SHANK Ø 2.35 & 3.00 MM Mandrels suitable for our various unmounted tools.
SMOXH Cutting Tools offers you quality, time, and cost savings simultaneously. Our tools, constantly updated with innovations every day, guarantee that quality doesn't have to come at a high price
Clamping range: 10 mm - 40 mm
Carrying your RAD pneumatic tool around from job to job? Introducing the RAD Tool Holder. We’ve continued our quest for improved ergonomics by not only engineering the world’s lightest pneumatic torque wrenches with the highest power-to-weight ...
A bore have been machined, even when its inner diameter was bigger than the entrance hole.
... use with any manufacturers equipment. Specify square size and thread type (if applicable ) on either end of quick change chuck / adaptor when ordering.
Universal tool system for all production areas Tool change within seconds Form-closing for reliable torque transmission Very short design Internal coolant supply is possible Presetting of tools outside the machine Tool holders in ...
Hommel+Keller Präzisionswerkzeuge GmbH
Standardised to DIN 69893 No retention nob Smaller (ca. 30%) and lighter (ca. 50%) than the steep taper (SK) Faster and easier tool change Rigidity 5 to 7 times higher than with steep taper holders due to support on the tool holder ...
Hommel+Keller Präzisionswerkzeuge GmbH
Standardised to DIN 69871 with retention knob Torque transmission by means of the friction contact of the taper with low strain For larger torques and sudden loads, driving keys are primarily responsible for the transmission The ...
Hommel+Keller Präzisionswerkzeuge GmbH
Clamping range: 0.31 in - 1.25 in
Rotational speed: 12,690 rpm - 60,000 rpm
Cylindrical Shank Chip Surfer Connection Neck Relief Shank modifications can be made by cutting off the back to desired length or turning back neck for more usable length
Ingersoll Cutting Tools
Designed for use with Scotch-Brite™ Clean and Strip Disc 2" shank lengthens reach of disc, helping operators access hard-to-reach areas of the workpiece Aids in swift attachment of disc to power tool, enhancing overall throughput and ...
Clamping range: 16 mm - 25 mm
... tool overhang, compared to standard milling chucks. A mono-block holder also allows stable machining even with larger diameter tools, thereby achieving higher efficiency machining. When a standard milling chuck ...
MITSUBISHI MATERIALS
Tungaloy has added high pressure coolant-through toolholders to its AddForceCut parting and deep grooving tool system. AddForceCut uses a unique insert clamping solution that makes a single-ended insert self-locked into the insert ...
Clamping range: 32, 35, 42, 50, 63 mm
Grip (2:1 advantage). Uses and application Shank - Cylindrical Plain Drilling - Through Coolant Axial Adjustment - End Collet - ER DIN 6499 Shank - SK BT JIS B 6339 Shank - Cylindrical with Square ER Solid Collet 100042742 Shank ...
Widia Manchester
Many parts that previously were made in cam type machines and traditional CNC machines are now produced in Swiss / Sliding head automatic lathes. Machining in these machines is different from machining in traditional machines and the ...
Whizcut of Sweden AB
Tool Holders for Telescoping Torque Arms Multi-Position Tool Holders for Telescoping Torque Arms Tool Holders for Torque Tubes Tool Holders for Folding and Linear Torque Arms Swivel Holders for Select Arms
ASG Division of Jergens
Tap holder with ratchet, short + long for right- and left-hand-turn
Please specify:
Help us improve:
remaining