Control valves

DN: 100 mm - 400 mm
Pressure: 0.2 bar

VFP/VFPX Butterfly Valves can be fitted beneath hoppers, bins, silos, screw or other type conveyors, or to intercept pneumatic conveying ducts. Due to their special design material residue between valve ...

DN: 240 mm - 600 mm

... hoppers, or bins, VFF Silo Closure Butterfly Valves are used in all types of building material processing plants where interception of gravity-fed dry materials is required. VFF-type Silo Closure Butterfly Valves ...

DN: 100 mm - 140 mm
Pressure: 2.5 bar
Temperature: -20 °C - 90 °C

VW Butterfly Valves are the ideal solution for the interception of gravity-fed or pneumatically conveyed dry powders or granules in a variety of bulk solids handling and processing plants. VW Butterfly Valves ...

DN: 16 mm

In-line valve VS 16, stainless steel, small flange KF DN 16 The VS und VS C series valves are butterfly-type valves. A circular valve plate with a sealing ring on the ...

DN: 0.25 in
Pressure: 50 psi - 5,000 psi
Flow rate: 0 l/h - 23 l/h

This high pressure miniature pressure compensating flow control valve is only .250” in diameter and 1.38” in length. This valve provides a constant flow rate over a wide range of pressure ...

Pressure: 10 bar - 17 bar
Temperature: -20 °C - 65 °C
Flow rate: 21 l/s

Assists machine designers in complying with the European Machineries Directive Can help existing machinery to comply with PUWER (Provision and Use of Work Equipment Regulations) Controlled increase of downstream pressure ...

Pressure: 17, 10, 3 bar
Temperature: -20 °C - 80 °C
Flow rate: 147 l/s

Assists machine designers in complying with the European Machineries Directive Can help existing machinery to comply with PUWER (Provision and Use of Work Equipment Regulations) Controlled increase of downstream pressure ...

DN: 20 mm
Pressure: 0.4 bar - 8 bar
Temperature: -20 °C - 85 °C

... flow rate Simple construction for ease of maintenance One piece diaphragm for longer life Control via separate pilot valve or control unit Medium: - Compressed Air Port ...

DN: 8 mm - 80 mm
Pressure: 40, 63 bar
Temperature: -20 °C - 80 °C

Actuated valves in the RV-FLUID series consist of a pneumatic rotary actuator series R4 that controls a ball or a butterfly valve. Ball valves come in the 2- and the ...

DN: 6, 8, 4 mm
Pressure: 1 bar - 10 bar
Temperature: -20 °C - 60 °C

... thread and push-in fitting. The main feature of these valves is that the discharge flow can be adjusted via a pin regulator. This allows you to control the speed of the actuator connected to the valve, ...

DN: 0.25, 0.5 mm
Pressure: 2 bar - 10 bar
Temperature: -10 °C - 70 °C

... progressive starter is a valve that regulates the flow of air until the outlet pressure reaches a certain value, at which the valve opens and allows air to flow at full rate. This valve ...

DN: 0 mm - 1.5 mm
Pressure: 0 bar - 34.7 bar

The needle valve is an adjustable orifice, which can be used to control flow rates, mini-cylinders, nozzles, timing circuits, filling heads, bleed vents, and in many other applications. The adjusted flow ...

DN: 0.28 mm - 1.4 mm
Pressure: 0 psi - 200 psi

... orifice and check valve. The orifice meters flow in the forward direction, while the check valve permits free return flow. This valve is particularly well suited for control ...

DN: 0 mm - 1.4 mm
Pressure: 0 psi - 200 psi

The Beswick MIL-MV series metering valve contains an adjustable orifice. The orifice meters fluid flow, regardless of flow direction through the valve. The o-ring seals fit to make the valve ...

DN: 40 mm - 100 mm
Pressure: 73, 145, 87, 116 psi
Temperature: 275, 284 °F

Valves / Mixproof Valves The DT4 tank outlet mixproof valve is used for the reliable separation between the tank and servicing pipeline. The DT4 tank outlet is an extension to ...

DN: 1.5 in - 6 in
Pressure: 5 bar
Temperature: 135, 140 °C

The next generation of mixproof valve technology is the result of continued development from both APV and Waukesha Cherry-Burrell process technologies. Used for the reliable separation of dissimilar fluids, the D4 Series ...

DN: 38 mm - 152 mm
Pressure: 10, 6 bar

The W72RS Series Mix Proof Valve features a lower radial seal for minimal spillage of products when opening or closing. Specifications Materials Product Wetted: ASTM 316L (UNS-S31603); (DIN-1.4404) Non-Product: ...

DN: 15 mm - 65 mm
Pressure: 10 bar
Temperature: -20 °C - 120 °C

DIALOCK® diaphragm valve with stroke limiter and male ends for solvent welding, metric series. The DK DIALOCK® diaphragm valve is particularly suitable for shutting off and regulating abrasive or dirty ...

DN: 15 mm - 65 mm
Pressure: 10 bar
Temperature: -20 °C - 120 °C

Pneumatically actuated diaphragm valve with male ends, metric series. Normally Closed function. The DK diaphragm valve is particularly suitable for shutting off and regulating abrasive or dirty fluids. ...

DN: 15 mm - 65 mm
Pressure: 6 bar

Pneumatically actuated diaphragm valve with male ends for solvent welding, metric series. Normally Closed function. The new DKB/CP diaphragm valve is the proper solution for non-severe operating conditions ...

DN: 40, 32, 50 mm
Pressure: 10 bar
Temperature: -10 °C - 100 °C

... onboard Semiconductor temperature sensor OPERATION Not only hâve the Diamix L and Compamix L mixing/thermoregulating valves a fixed point régulation function. but they also feature a spécifie software wfiich allows ...

DN: 10 mm - 40 mm
Pressure: 16 bar
Temperature: 0 °C - 60 °C

2-way FF PVC with connection kit Version with threaded or to-be-glued connections

DN: 32, 40, 50 mm
Pressure: 40 bar
Temperature: -20 °C - 50 °C

... limit microswitches internal anti-condensing heating spacer for insulation with manual override thermal break between ball valve and actuator THERMAL BREAK The material of the thermal break is a compound with self-lubricating ...

DN: 25 mm - 400 mm
Pressure: 0 bar - 10 bar
Temperature: 220 °C

... precise control of the flow rate through concentric Iris® diaphragms (similar to a camera diaphragm). - Energy-saving and low-noise control valve due to its free centric passage. - ...

DN: 25 mm - 400 mm
Pressure: 0 bar - 10 bar
Temperature: 180 °C

Energy saving valve for the precise and economical control at low loss of pressure of liquids and gases that can be either clean or contain particles. For : Air for aeration in wastewater treatment ...

DN: 0.125 in
Pressure: 0 bar - 34.5 bar
Temperature: 0 °C - 121 °C

... 90 degree flow patterns Valves are offered in straight (T) and 90 degree (L) flow patterns. All valves are supplied with 1/8” FNPT inlet and outlet ports. Valve cartridges are ...

DN: 3.175 mm
Pressure: 0 bar - 5.2 bar
Temperature: 0 °F - 150 °F

... reliable PTFE needle valves are designed for laboratory and industrial applications for regulating corrosive gases and liquids or for high purity service. They may also be used as shut off valves. Pliant ...

... conditions could make impossible to use any other kind of dispenser. These metering valves are the double checking version of some Double line metering valves. The use of these units is required ...

Pressure: 3 bar - 10 bar

This valve has been designed to control lubricant flow (oil and grease). Piston is made of hardened and ground steel. It is driven by a pneumatic cylinder controlled by a 4-way solenoid valve. This ...

Pressure: 400 bar
Temperature: -10 °C - 50 °C

The 4/2 electropneumatic valve has been designed to control the supply of lubrication in dual-line systems (system 2). It is capable of operating with NLGI 2 MAX grease at a maximum pressure of 400 bar ...

DN: 6, 8, 4 mm
Pressure: 0.2 bar - 10 bar
Temperature: 5 °C - 80 °C

FLOW CONTROL VALVES - WITH SWIVEL JOINT ► Configurable flow control valves for regulating the exhaust air ► Optimal for regulating the speeds during piston movements ► ...

Pressure: 0 bar - 10 bar
Temperature: -25 °C - 85 °C

Certificates: Tested and Proven for Automative applications

Pressure: 0 bar - 10 bar
Temperature: -25 °C - 85 °C

Certificates: Tested and Proven for Automative applications

Pressure: 0 bar - 10 bar
Temperature: -25 °C - 85 °C

Certificates: Tested and Proven for Automative applications

DN: 0.25 in - 2 in
Pressure: 1,200 psi
Temperature: -60 °F - 450 °F

Part Material Body - CF8M or SUS316 Body Cap - CF8M or SUS316 Bail - CF8M or SUS316 Retainer - CF8M or SUS316 Stem - SUS316 Seat - PTFE+15% GF Seal - PTFE Thrust - PTFE Stem Packing - PTFE Stem Gland - SUS304 Stem Nut - SUS304 Handle ...

DN: 1, 0.75, 0.5 in
Pressure: 400, 350, 500 bar
Temperature: -20 °C - 125 °C

Pilling-Up directional control valve single or double acting. From 1 to 7 sections, with relief valve and multiple configuration options.

DN: 0.75, 0.5 mm
Pressure: 0 bar - 350 bar

Mechanical valve to control the cylinder’s position.

DN: 6 mm - 80 mm
Pressure: 0 bar - 25 bar
Temperature: -10 °C - 180 °C

Globe valve - 507 The GEMÜ 507 2/2-way angle seat globe valve has an ergonomically designed plastic handwheel and is manually operated. The valve spindle is sealed by a self-adjusting ...

DN: 15 mm - 100 mm
Pressure: 0 bar - 40 bar
Temperature: -10 °C - 60 °C

... 539 2/2-way globe valve has a hollow shaft actuator and is electrically operated. The eSyDrive hollow shaft actuator can be operated as an OPEN/CLOSE actuator or as an actuator with integrated positioner or process controller. ...

DN: 4 mm - 25 mm
Pressure: 0 bar - 8 bar
Temperature: -10 °C - 100 °C

Diaphragm valve - 650TL Diaphragm valve GEMÜ 650TL is a manual tapping valve with automatic closing function which is pneumatically operated. The "keep-closed" override of manual operation ...

DN: 0.5 mm - 0.9 mm
Pressure: 7 bar
Temperature: -10 °C - 50 °C

DN: 1.2 mm - 1.6 mm
Pressure: 0 bar - 6 bar
Temperature: -10 °C - 50 °C

DN: 2 mm
Pressure: 0 bar - 12 bar
Temperature: -10 °C - 70 °C

The Poppet Valve is especially constructed to be utilized in control and panel units. Through its hexagonal construction, the valve is able to be used even in minimal spaces. Various ...