Control valves

DN: 25 mm - 700 mm
Pressure: 10 bar - 100 bar

... and accurate control The valve segment comes with dual bearings which results in high durability and low torque requirement The valve seat can be replaced from the outside without ...

DN: 50 mm - 200 mm
Pressure: 0 bar - 10 bar
Temperature: 0 °C - 150 °C

... combination with the flushing chambers prevent any contact of the product with the environment. On the inside of the valve, the self-draining valve housing with single-seat, leakage chamber and balancer ...

DN: 0.5 in - 6 in
Pressure: 230 psi

Type-21/21a ball valves are corrosion resistant plastic manual true union design quarter turn valves with hyperbolic flow characteristics, low pressure drops and reliable sealing. They offer relatively ...

... downstream pressure to a re-determined limit. Wnen downstream pressure exceeds the pressure setting of the control pilot, the main valve and pilot valve close drip-tight.

DN: 15 mm - 50 mm
Pressure: 40 bar
Temperature: -30 °C - 140 °C

Control ball valve to control the flow of hot and cold water and Glykol solutions (max. 50%) in HVAC systems conjunction with a rotary actuator Technical data Valve Flow ...

DN: 50 mm
Pressure: 10 bar
Temperature: -20 °C

The sampling valve 125A is standard DN50 sampling valve by FAMAT. It is used for sampling of powders, granules, pastes and liquids under process conditions in the pharmaceutical, chemical and food industries.

DN: 0.5 in - 2 in
Pressure: 41.4 bar
Temperature: 400 °F

The NIBCO® bronze ball valve provides bubble-tight shutoff at 600 PSI. The valve is equipped with integral ISO direct mount pad for actuation and vented ball. It is pre-assembled with NIBCO® Series 2000 ...

DN: 40 mm - 600 mm
Pressure: 10, 16 bar
Temperature: 50 °C

Resilient-seated gate valve with bolted cover connection and face-to-face length of Basic Series 14 for waste-water applications. Proven design with innovative improvements, such as plastic sliding caps on the wedge, ...

DN: 0.25 in - 2 in
Pressure: 1,000 psi

AISI-316 (ASTM-A351-CF8M, EN10213 1.4408), AISI-304 (ASTM-A351-CF8, EN10213 1.4308) Full port, Threaded end, 1000PSI/ PN63, Blow-out proof stem Locking device, Oval handle, Wing handle

DN: 15 mm - 150 mm
Pressure: 16 bar
Temperature: -40 °C - 210 °C

... PFA lined ball valves are used in a wide variety of applications in many industries The valves are ideally suited for corrosive applications, requiring reliable performance, tight shutoff, constant ...

DN: 16, 25, 40, 50 mm

Soft start valves are used to throttle the gas flow in roughing lines. They prevent turbulences in piping and containers, particulate contamination in vacuum installations, detachment of substrates by turbulences.

DN: 15 mm - 300 mm
Pressure: 4 bar - 10 bar

DN 15 - 200 PN 4 - 10 Body: EN-JL1040 Coating: Rubber lining, Halar Diaphragm valve with or without rubber coating, and different qualities of diaphragm for different media. Drip-proof closure even with suspended ...

DN: 10 mm - 300 mm
Pressure: 40 bar
Temperature: -271 °C - -30 °C

... environment, desert or cold conditions) Essential product features: - Available as globe, control or check valve and filter with stem extension - Cryogenic valve suitable for medium ...

DN: 3 mm - 8 mm

... Intake Shutoff Valve is available with three different methods of electric actuation described below. The descriptions include the available models for each version. -SVX Energize To Close Valve ...

Gate valves Gate valves are primarily used to enable or prevent a fluid medium to flow (i.e. ON / OFF control). A fully open gate valve results in no obstruction to ...

DN: 0.5 mm - 11 mm
Pressure: 0.5 bar - 10 bar
Temperature: -10 °C - 70 °C

... at least 10°C below lowest occurring ambient temperature. Materials Body: Al (anodized), seals: NBR This valve is used for the speed control of a pneumatic cylinder. The flow rate can br regulated ...

DN: 0.25 in - 2 in
Pressure: 400 psi

Threaded, 2-Piece, Std. Port, Bronze Ball Valve, 400 CWP, Sizes: 1/4" to 2" (DN 8 to DN 50)

The actuator pilots of the OS Series are especially designed for pressure control in regulators and shutoff valves, they can operate on maximum and minimum pressure, on maximum only, on minimum only.

DN: 0.5 in - 3 in

Series CSM-61 Flow Measurement Valves monitor system flow in low to medium flow rate HVAC units providing a highly accurate flow measurement. It consists of bronze body construction with bi-directional, positive shutoff ...

DN: 50 mm - 300 mm
Pressure: 6, 10 bar
Temperature: 10 °C - 60 °C

• Ideally suited for flow control using minimal piping space. • 100% factory tested. • Minimal pressure drop. • Low maintenance. • Resistance to many inorganic chemicals. • Regulable opening every 15º with position ...

Pressure: 240 bar

... one. Therefore, a four valve block, as an example, can actually serve anywhere between four and eight bearings. DM series valves always have one discharge port per valve section located ...

DN: 16 µm - 250 µm

A 5-port valve utilizing a soft spool and is environmentally resistant (unfiltered air) and compatible in a wide range of fields. [Compatible cylinder] Dia.6 to Dia.250

... over air relay valve. These valves output air pressure in proportion to the hydraulic input pressure. Hydraulic input pressure, from a component such as a master cylinder or hydraulic control ...

DN: 4 mm - 38 mm
Pressure: 350, 400, 500 bar
Temperature: -20 °C - 80 °C

Connection 1 + 2 BSP cylindrical internal threads Sealing form 1 + 2 for screw-in pins with shapes A, B and if necessary E Note Bitte die Bedienungsanleitung für Kugelhähne beachten. Bitte die zul. Druckangaben ...

DN: 0.75, 0.5 in
Pressure: 150, 300 psi
Temperature: 358, 550 °F

... ’s Flow Control Four-V Port Globe Valves are equipped with a micrometer dial and pointer which enables the valve to set within 1/100th of a turn of the handwheel. This allows you to fine-tune ...