DC electromechanical relays

Switching current: 6 A

Force Guided Relays RF1V Series RF1V Series force guided relay have mechanically linked contacts allowing you to use in safety related circuits. Available in four or six pole models, all relays ...

Both electronic type and electromagnetic type relay available upon request; Min tripping power:100uVA; Magnetizing power:≥5000uVA; Resetting force: 1.2N-1.6N; Impedance when tripping power adjusted into 100uVA: 160 ...

The Class 47 alternator relay provides a means of automatically alternating the operation of two separately mounted motor driven pumps or compressors. This alternating action assures even readiness and wear on both pumps. ...

Switching current: 20 A - 63 A

... pole. Are you looking for savings in electric energy? Replace installation relays and contactors with latching relays. At remote switching of lighting, a parallel connection of pushbuttons is used. ...

... is a DC neutral line relay fitted with independent non-fusible contacts. It meets the requirements of relevant BRB Spec. Relay types covered under this category are: QN1 - Line ...

Switching current: 5 mA - 8,000 mA
Output voltage: 120, 24, 250, 240 V
Output current: 0.1 A - 8 A

... 2NO; colis AC or DC; for PCB and sockets Contact data Coil data Rated power consumption :AC: 0,75 VA; DC: 0,4 ... 0,48 W General data Mechanical life (cycles) :>3 x 107 Ambient temperature ...

Output voltage: 250 V
Output current: 10 A

The JQC-3FF is a subminiature high-power relay commonly used in a variety of applications. It is a general-purpose, high-current relay that can switch loads up to 10A at 250V AC or 30V DC. ...

Switching current: 100 A

1.Single phase 100A switching capability; 2.Multi-layer blades, low temperature rise; 3.Low contact resistance < 1.0mΩ; 4.Environmental protection (comply with ROSH) ; 5.Outline dimension:43.2mm×33.2mm×22mm 6.Applied in Electronic ...

Switching current: 4.4 A - 87.8 A

... function minimum space design. Suitable for 50 Hz and 60 Hz frequency cycles. Available in 6, 12, 24, 110, 220 & 240V AC and DC. Built in Diode models with contact capacity of 10 Amperes. Features: • Compact housing ...

Output voltage: 230 V
Output current: 0 A - 6 A

• PLC transistor output to power switching converter • common positive or negative • LED indicators for output relays coil voltage nominal voltage +10% / -15% duty cycle 100% screw tightening torque 0,6...0,8Nm operating ...

Switching current: 10 A

Compact Industrial plug in relays with built in features like LED, Free wheeling Diode, Polarity Diode, RC, Bridge Rectifier, Magnetic Blow out Relay for Inductive load and Twin contacts for low switching ...

Switching current: 5 A

Series 37 Mounting Style: Plug-In Contact Form: 2C, 4C Rating: 5 A at 24VDC/230VAC Coil: 12-110 VDC, 110, 230 VAC

Switching current: 16 A

... deep. State-of-the-art hybrid technology combines advantages of nonwearing electronic control with high capacity of special relays. With the patented Eltako Duplex technology (DX) the normally potential-free contacts can ...

Switching current: 8 A - 16 A

... color for output status indication: red, green, yellow, blue or white LED* Inbuilt diode for suppressing unwanted peaks while relay opening and RC element against disturbances 1- MODULE, DIN rail mounting

Switching current: 16 A

All-or-Nothing relays for AC and DC high power switching operation. Design includes a clear protective dust cover and two or three-pole contact configuration rated 4KVA-16A-250VAC.(6.3x0.8mm) Standard ...

Output current: 8 A
Width: 14 mm

Interface modules-breadth 6,2mm and 14mm | Relay interface modules Technical Data Relay input signaling led Drawbar for din bar Two 8A exchange contacts 8 Pole comb for in parallel interface ...

Switching current: 2.5 A - 30 A

High voltage relays for disconnecting and switching over of test paths and for the configuration of switch matrixes. These relays can be connected directly to a SCHLEICH test device via a 24 V DC ...

Switching current: 20 A

The 295 Series, manufactured by Deltrol Controls, is a power relay that is integrated with a rated current that ranges from 15 up to 50 amperes and a total temperature of 155°C. This is used in a wide range of applications ...

Start relay for starters – solenoid Completes the circuit that brings electric current from a vehicle's battery to the starter motor of the engine. Mounted in heavy duty vehicle engines. Designed and manufactured ...

Switching current: 6 A - 110 A
Output voltage: 30, 28 V
Output current: 10 A

Chordn provides various electromechanical relays in 6 different types and each with multiple sizes for extremely wide application. Our products are compatible to wide control voltage, different contact ...

Switching current: 10 mA - 10,000 mA

... auxiliary relay with self-reset or latching contacts and hand reset flag The Delta MSARD4 is a high performance electro-mechanical auxiliary relay for power utility protection and control ...

Switching current: 0.5, 11, 15 A

... available for holding or indicating as follows: E40, 11A, 250V AC; E60, 15A, 250V AC and 1/2A, 125V DC; E100 and E150, 15A, 480V AC and 1/2A, 125V DC. Other auxiliary contact ratings are available.

... switch operating contacts in response to impulses from a solid-state electronic timing circuit. Automatic Reclosing Relay Protective relays are often interested from unwanted opening due to temporary ...