Electronic amplifiers

Voltage: 110, 220 V
Current: 100, 1 mA
Frequency: 50, 60 Hz

DP-300 Series amplifiers are AC/DC differential amplifiers highly suited for EEG, EKG and extracellular recording. Features include high input impedance, high common mode rejection [100 dB @ 60 Hz], low ...

Voltage: 207 V - 253 V
Current: 2 A
Power: 2 W

Application: Isolating switch amplifier with intrinsically safe control circuit class [Ex ia] IIC for inductive contacts according to DIN 19234 or NAMUR or mechanical contacts in hazardous industrial plants. Case:NORYL ...

Avago Technologies offers a broad selection of rf and microwave amplifiers including Power Amplifiers (PAs), Gain Blocks/Drivers, Low Noise Amplifiers (LNAs) and variable gain amplifiers ...

Diodes op-amp range provides Industry standard parts for general purpose consumer and industrial applications. Many devices are specification matched and pin for pin compatible with industry standard parts.

Voltage: 200 V
Current: 10 A
Power: 100 W

The MP108 is a 10A, 200V power operational amplifier that features a very high 300kHz of power bandwidth for piezoelectric actuator and transducer drive applications. The MP108 has optional features such as four-wire ...

Voltage: 100 V - 230 V
Power: 0 W - 3 W
Frequency: 1 kHz - 50 kHz

... applications the new MOPA microlasers from STANDA utilize Master Oscillator Power Amplifier platform that combines company's renowned STA-01 microlaser oscillators together with a highly efficient amplifying ...

Voltage: 10 V

... decoupled - patent no. 196 52 293 - reusable for other measuring tasks PERFECTLY CONDITIONED. UNIVERSAL. The measuring amplifier MA-UNI adjusts signals of different type and size to the 5V input of a PC data acquisition ...

Voltage: 5 V
Current: 5 mA
Frequency: 100 kHz - 10,000 kHz

Looking for a time code distribution solution? Need even more outputs? Is your installation spread across a wider geographic area? Is a second clock not practical? The Model 1073A was built to address these and other challenges, while ...

Voltage: 2.5 V
Frequency: 4 MHz

... Multiplier Applications - Analog computation Squaring circuits Modulation and demodulation Voltage controlled amplifiers Features - MLT04 replacement Four independent channels Four-quadrant ...

These transimpedance amplifiers are particularly useful for the measurement of current from photodiodes. The output is a voltage linearly proportional to input current and thus, to input power in photodiode monitoring ...

Voltage: 0 V - 10 V
Current: 0 mA - 20 mA

... Housing for DIN rail mounting 12-pole, 82 x 22.5 x 98.8 mm (h x w x d) Brief Description The active universal isolating amplifier HE 501 serves for the galvanic separation of measuring circuits, which are on different ...

Voltage: 24, 115, 230 V

... photoelectric amplifier developed by Telco Sensors. It is specifically designed to be used in conjunction with a set of LT remote transmitter and LR receiver from the 101/100/110 or 120 selection. The amplifier ...

The 4711A1 series from Dytran is an in-line charge amplifier that is especially designed with stainless steel to ensure highly durable performance when in use. It features a 10-32 jack input connector and a BNC plug ...

Digital power amplifier for single solenoid and double solenoid valves Usable as a replacement of PAM-195, PAM-196 and PAM-197 For all typical proportional valves of all manufacturers ...

Voltage: 0 V - 10 V
Current: 4 mA - 20 mA

... cell amplifiers measure just 19mm in diameter and 7.6mm in height and are designed for incorporation into the body of a broad range of strain gauge transducers and load cells. When internal mounting is not possible, ...

Voltage: 5 V

Voltage: 1.8 V - 5.5 V

This IC is an audio power amp that can operate at low voltage. Operating supply voltage supports 3V and 5V power amp, making it ideal for applications such as mobile phones and other portable communication devices. It is equipped with ...

... areas needing galvanic isolated amplifiers Measuring : distortion, pressure, force (gauge sensor) DESCRIPTION E300F4 amplifier conditioner can be used twofold: strain gauge sensor conditioner high precision ...

Voltage: 0.5 V - 10 V
Frequency: 1 Hz - 10,000 Hz

... Signal Conditioning and amplifier’s low-level signals to high-level outputs for multiple channels can be simultaneously and dynamically recorded and displayed on external devices. Features • - Differential signal ...

Voltage: 24 V
Current: 10 mA

Designed for strain gage sensors or potentiometers DIN rail fixture Front panel calibration shunt Compatible with the MCS trigger level modules The MCJ conditioner is fixed on a DIN rail in a polyamide casing. the I/O electrical connection ...

... distribution features in one time and frequency distribution unit. The base unit is a dual input, 24 output frequency distribution amplifier suited for 5MHz or 10MHz. Each output is monitored and will set the alarm ...

Voltage: 3.3 V

The PAD2 is a portable and universally usable forcemeasurement amplifier with a digital display. The samplingfrequency can be adjusted in the range of 10 Hz (slow),20 Hz (medium) and 100 Hz (fast). The ...

The F6300 High-Power Current Amplifier works in combination with the F6150 Power System Simulator to bring your realistic protection scheme testing power to the next level. This combination allows you to evaluate the ...

Voltage: 0.5 mV - 10 mV
Current: 4 mA - 20 mA
Frequency: 1,000 Hz

FUTEK's IAA200 Analog Amplifier with Current Output is FUTEK’s brand new general purpose amplifier solution for in-line amplification of any full bridge strain gauge type sensor with mV/V range output. ...