Frequency: 315 MHz
Designed for 315.00 MHz Applications • Advanced (Lithium Tantalate) LiTa 03 Design for Low Insertion Loss • Designed for Match to 50W, No External LC Required • Hermetically Sealed Surface Mount Package • Complies ...
RF Monolithics
Frequency: 10 Hz - 55 Hz
Voltage: 12 V - 30 V
Primary current: 4,000, 500 mA
S15F in-line filters are small, plug-in accessories designed to connect directly to a sensor, indicator, or other device. They fit seamlessly into your factory applications and begin operating immediately to suppress ...
Frequency: 60, 50 Hz
Voltage: 400, 690 V
Primary current: 30 A - 150 A
... series Active Harmonic Filter is a new type of power quality improvement products for the harmonic distortion in the circuit. With the advantage of the Fast Fourier Transform(FFT) and 3-Level technology, the SFR-APF Active ...
Frequency: 50, 60 Hz
Voltage: 400, 690 V
Primary current: 30 A - 150 A
... series Active Harmonic Filter is a new type of power quality improvement products for the harmonic distortion in the circuit. With the advantage of the Fast Fourier Transform(FFT) and 3-Level technology, the SFR-APF Active ...
Frequency: 60, 50 Hz
Voltage: 400 V
Primary current: 100 A - 10,000 A
Harmonic current generator The Aunilec APF behaves like an harmonics current generator. It will measure the harmonic generated from the non-linear loads and cancel these harmonics with an opposite phase at the same amplitude. Power ...
Frequency: 50 Hz - 60 Hz
Voltage: min 230.0 V
... electrostatic filters with built-in electronics, for oil and oily vapour applications. FEL SYSTEM represents a revolutionary development and a valid alternative to traditional filters. ...
Voltage: 75 V
Primary current: 10 A
Rated at 10A with a maximum voltage of 75V, this board mounted EMC filter offers exceptional differential mode performance, making it ideal for use with DC-DC converters and thus saving on printed circuit board area. ...
Frequency: 40, 5, 900 kHz
Low Pass Filters for DC Looms Oxford Instruments offer a selection of low pass multi-stage filters for our 24 way DC looms.The low pass filters are available in four different cut-off ...
Frequency: 50, 60 Hz
Voltage: 208 V - 690 V
Primary current: 47 A - 300 A
Eaton’s HCU2 is a static power electronic unit that provides dynamic L-L harmonic mitigation in most industrial applications. Its fast reaction to correcting nonlinear loads and power factor make this product an ideal ...
Frequency: 110 kHz - 140 kHz
Voltage: 230 V
Primary current: 2 A
The mains filter up to 2A 230V/50Hz is designed as a built-in filter. It attenuates interference signals from the consumer to the actuator and prevents that disturbances from the connected consumers are ...
Technical Specifications Industrial Pull UP I2C connection (includes 2 units): PT 4 Feed-Through and Multi-Conductor Terminal Blocks 50 % less insertion force. Compact design and front connection facilitate wiring in the tightest ...
Frequency: 50 Hz - 60 Hz
Voltage: 220 V - 690 V
Primary current: 100 A
Active Power Filter (APF) Model Number: APF 3P3W 50A – 200A, APF 3P4W 50A – 200A Nominal Capacity: 50 A – 200A Nominal Voltage: 220VAC, 400VAC, 690VAC Nominal Frequency: 50HZ/60HZ Installation method: Stand, Wall Mount Application ...
Shenzhen Consnant Technology Co., Ltd.
Frequency: 50, 60 Hz
Voltage: 460 V
Primary current: 20, 45 A
The use of line reactors is optional for 3-phase line filters. This reduces the voltage distortions (THD) in the mains and increases the service life of the servo amplifier. Similar to line filters, several ...
Please specify:
Help us improve:
remaining