- Power Transmission - Mechanical components >
- Mechanical Transmission >
- Flexible coupling
Flexible couplings
Torque: 7.5 Nm - 940 Nm
Rotational speed: 5,000 rpm - 20,000 rpm
The jaw coupling is a general-purpose transmission coupling that is widely used in motion control (servo) systems. Its purpose is to transmit torque (by connecting the two shafts) while absorbing damping ...
GUANGZHOU LINK AUTOMATION EQUIPMENTCO., LTD
Torque: 31 Nm - 7,200 Nm
Couplings TORSIONAL FLEXIBLE COUPLINGS - “GEB HRC”
Torque: 14,675 Nm
The FFX series is manufactured by Challenge PT, and is a shaft coupling with torque output of up to 14675 Nm at 6 pole motors. It has an angular misalignment of up to 4° with wind up shock absorption of up to 12°. The ...
Challenge Power Transmission Plc
UHV rated to 1x10-13 High temperature rated to 450ºC OFE Copper or optional Viton® elastomer gaskets Clearance bolt holes Conflat® compatible design Standard matte finish Used for short misalignment connections ...
... gear couplings of our own design. They are easier to connect or disconnect than chain couplings. ● The gear teeth of the inner hubs are crowned to allow for up to 5° of shaft angle offset. ● Due to induction ...
GN couplings are made up of two toothed steel bushings, connected by a nylon ring with internal toothing. A snap ring at the centre of the hole prevents axial displacement. GN couplings are only available ...
Different sizes and rubber quality. Standard Hardness 85 Sh.
TALLERES EGAÑA
Torque: 1.28 Nm - 33.5 Nm
Rotational speed: 4,000 rpm - 14,000 rpm
... displacement values are dependent on the RPM and power output. Careful alignment of the shafts increases the service life of the coupling. max. misalignment axial: ± 3,4 mm max. misalignment radial: ± 0,5 mm max. misalignment ...
Technische Antriebselemente GmbH
... . - The individual safety element cannot be overloadedif correctly chosen. - Exsisting shear-pin couplings can be replaced by MALMEDIE Safety-Couplings.
Torque: 15 Nm - 10,000 Nm
Metal bellows coupling with simple flange mounting Features For simple flange mounting to special drive components Custom flange patterns available Temperature range -30 °C to +100 °C (-22 °F to +212 °F) Design Two ...
R+W Italia S.r.l
Torque: 15 Nm - 4,800 Nm
Rotational speed: 3,300 rpm - 22,200 rpm
... hole Chain CouplingsIn addition to our standard range, chain couplings are also availablein other sizes and in stainless steel - please inquire.Jaw Type CouplingsOur standard range offers couplings for ...
... function of a hydraulic shaft coupling (WHS) is the safe and backlash-free connection of two shaft ends by means of frictional engagement. For example, between an input and output shaft and mainly for transmitting torque. ...
Torque: 0 Nm - 1,100 Nm
Rotational speed: 30,000 rpm
Sliced couplings - Highlights The ASK sliced coupling is a solution for equalizing all kinds of offset. Its unique slit structure once revolutionized the coupling industry – over the ...
VMA Antriebstechnik GmbH
Torque: 190 Nm - 3,600 Nm
So far; the range of Conveyor Belts varies from half inch small pitch to 2 inch pitch running Conveyor Belt and solutions. The different series are offered in many variations to suit any application.
Hangzhou Ocean Industry co.,Ltd
Rotational speed: 50 rpm - 3,450 rpm
FC Series Insert 3-Jaw Type Couplings are available in Steel and are available precision machined bored or solid hubs. The FC Series coupling offers three types of inserts for different service requirements. ...
Boston Gear
Torque: 1.47 Nm - 23.43 Nm
Michaud Chailly
The original no hub coupling that is made in USA. A high quality low cost alternative where structural reinforcement does not require the use of a heavy duty coupling. In full compliance with ASTM 564, ...
Tridon Clamp Products
Rotational speed: 2,200 rpm - 7,200 rpm
... and quite transmission of the movement between driver and driven unit. This type of couplings allows absorbing shocks and torsional vibrations, thanks to particular elastic round-shaped inserts that work ...
Meccanica Couplings srl
Torque: 1.1 Nm - 1,500 Nm
Rotational speed: 1,750 rpm - 10,000 rpm
Basic Series ( COUPLINGS WITH HUBS ) to assemble with bore and keyway. With the same spider size, different coupling models can be interchanged, as well as with other coupling SERIES.
ALBERT
Weasler jaw couplings dampen system vibrations and adjust misalignment while transmitting torque in motion control applications, protecting other PTO driveshaft components from damage. Complete jaw couplers are available ...
Weasler
Torque: 10 Nm - 56,000 Nm
Rotational speed: 500, 750, 1,000, 1,500, 3,000 rpm
... advanced design and broad selection of couplings, which includes torsional rigid couplings, torsional flexible couplings, toothed couplings, couplings ...
... , radial, and angular shaft misalignments. Gear couplings are truly all-purpose and are used in numerous different applications. A wide range of combinations, for example with HYGUARD® safety couplings, ...
RENK GmbH
Torque: 10 Nm - 4,200 Nm
Rotational speed: 2,700 rpm - 7,100 rpm
connects drive shaft and driven shaft like a universal cardan joint special solutions on request compensating axial, radial and angular misalignments backlash-free wear-free especially suitable ...
Maschinenfabrik Mönninghoff GmbH & Co. KG
Torque: 52 Nm - 15,000 Nm
The flexible Hadeflex® couplings are claw couplings with a flexible element to provide a torsionally flexible connection for shafts. The flexible elements excel in their wear resistance, ...
ENGAGE AND DISENGAGE OPERATING ON ONLY ONE SCREW - OPERATION BY TWO SIDES - SAFETY LOCKING WITH FRONT TEETH CONNECTION - PART WITH HEAT TREATMENTS TO AVOID WEAR DESIGNED TO TRANSMIT THE TORQUE VALUES OF OUR CARDAN SHAFTS
Your suggestions for improvement:
Receive updates on this section every two weeks.
Please refer to our Privacy Policy for details on how DirectIndustry processes your personal data.
- Brand list
- Manufacturer account
- Buyer account
- Our services
- Newsletter subscription
- About VirtualExpo Group
Please specify:
Help us improve:
remaining