Ejectors

Flat ejector pin, hardened, plasma-nitrided, oxidised flat ejector, Special Flat ejector pin, hardened Flat ejector pin, with corner radius, with DLC coating Flat ...

Blade ejectors • Ejector pins • Ejector pins, T.G.R. treated • Core pins of Ampco • Ejector sleeves • Ejector sleeves, stepless

Nozzle diameter: 1 mm - 25 mm

Polimold has permanent stock of several dimensions. Made of steel H13, ejector pins follow strict international standards. Available: Type A puller pin and Type C puller pin Subtitle: D1= Outside Diameter D2= ...

The in-mould air ejector is designed to be fitted into a composite or a metal mould (specific mould inserts can be provided for fitting the valve into either metal or composite moulds)The valve provides an efficient method ...

The TM series is a stainless steel eductor, manufactured by BEX. The product is operated using Venturi Structural Afiich systems that allow smaller pumps to circulate large volume of tank solution. It cna circulate four to five gallons ...

Ejectors are suitable for grippers where the need for high vacuum flow is not excessive. Ejectors are easy to integrate as only compressed air needs to be connected to the gripper. UniGripper ejectors ...

Nozzle diameter: 1 mm - 2 mm

... the pumps offer even more: thanks to their optimal nozzle geometry with additional nozzle stages, our TIVAtec multi-stage ejectors achieve a high degree of efficiency with low energy consumption at the same time.

Useful to release small undercuts, this ejector is pre-adjusted and height adjustable. Easy to install, machining is 90° to parting line. The Balinit C® coating offers smooth action.

Nozzle diameter: 300, 700, 500, 400 µm
Suction rate: 16 l/min
Pressure differential: 90,000 Pa

In-line Type Vacuum Ejector • Maximum flow rate: 16 l/min (ANR). • Maximum vacuum pressure: -90 kPA. • Nozzle diameters: 0.3, 0.4, 0.5 and 0.7 mm. • Dimensions: Overall length 47 to 59 mm. Ø 8.2 to 10.4 mm. • Weight: ...

Nozzle diameter: 1 mm - 4 mm
Suction rate: 100 l/min - 600 l/min
Pressure differential: 350,000, 330,000, 500,000 Pa

・Air consumption: 90% reduction (For the ZL3, ZL6) ・Weight: Max. 60% reduction [ZL112 (Existing model): 450 g R ZL1: 180 g] ・3-stage diffuser construction (For the ZL1:SMC comparison) 　Suction flow rate increased by 250% ・3 types ...

The EM80.1 Ejection Module from MBO was specially designed to allow printers to eject misprinted sheets, control sheets, and white-waste sheets without interrupting production. By eliminating these sheets via the EM80.1 Ejection Module, ...

Suction rate: 15 l/h

... 6 bar M 305 – Reinforced ejector for more than 4 kg/h, G 5/4 M 306 – Ejector with union connection for pressure up to 6 bar, max 4 kg/h M 307 – Reinforced ejector for pressures ...

powder pump • Design of a new efficient injector powder pump • The most effective feed angle demonstrated by research powder pump • Saves paint and air compared to right angle injectors powder pump •Compared to other pumps, ...

• Distribution in silos and bunkers • Conveying capacity: up to 160 m³/h • Drive power: 5.5 kW • Application: Bulk goods• Distribution in silos and bunkers • Conveying capacity: up to 160 m³/h • Drive power: 5.5 kW • Application: Bulk goods

Easy ejector rod Pascal Easy ejector rod makes an ejector rod changing dramatically easier It is a newly designed ejector rod with strong magnets on the joint surface of ...

Pressure differential: 6 bar

for the production of foam paint rollers The foam block is put onto the conveyor belt the position of the drill holes is controlled by a laser sensor the finished paint rollers are ejected from the foam block and collected in a case ...

UPE offers a choice of fixed tip angles: 11°, 22°, 31°, 39°, 45°. Treated steel tip plates provide weld spatter and corrosion resistance for durable operation in extreme environments. Integrated 70mm or 100mm bore pneumatic cylinder. Optional ...