Hydraulically-operated valves

... Differenlial PressureValveisa hydraulically operated pilot-controlled. modulating valve. It is designed to maintain a constant pressure differenlial between any two pressure points ina ...

The control valves with actuator are primarily used within the industrial plants to maintain operating conditions such as flow, pressure, temperature and liquid level by fully or partially opening or closing response ...

DN: 50 mm - 300 mm
Pressure: 10, 16 bar
Temperature: 50 °C

... sealing ring - Independent of variations of the inlet pressure / flow rate, the valve regulates a higher inlet pressure to a constant, lower outlet pressure - Valve controlled by its own medium - ...

DN: 50 mm - 1,500 mm
Pressure: 400 bar
Temperature: -196 °C - 450 °C

Trunnion mounted split body ball valves, double block and bleed function, for oil and gas standard and severe applications The FCT Split Body trunnion mounted ball valves have been designed for severe ...

Pressure: 2,500 psi
Flow rate: 2 us gal/min

The CROSS SQV series valve is a 2-position, 3 port valve designed to alternately operate a pair of agricultural guide marker cylinders. May be used with single acting or double acting marker cylinders. Features: 2500 ...

DN: 700 mm - 3,500 mm
Pressure: 6 bar - 40 bar

... Epoxy-Polymer-Ceramic (EPC) Tried and tested technology for nominal widths between DN 700 and DN 3600, variants with weightloaded hydraulic actuator available. Drinking water certificate.

DN: 56 mm - 188 mm
Pressure: 30 psi - 200 psi
Temperature: 125 °C

... engine’s primary source of fuel is taken away. An intake air shut-off valve is a must for diesel engines which have even a possibility of encountering hydrocarbon vapors. The Intake Air ...

Pressure: 240 bar

... one. Therefore, a four valve block, as an example, can actually serve anywhere between four and eight bearings. DM series valves always have one discharge port per valve section located ...

... variations. According to customers‘ information, valves are factory adjusted ready for operation and very simple to readjust if so desired. The patented up levelling system combined with compensated pilot ...

... variety of hydraulic systems. Power off-braking through limited stored energy in the accumulator(s). MICO also makes a hydraulic over air relay valve. These valves ...

DN: 25 mm
Pressure: 0 bar - 350 bar
Flow rate: 0 l/min - 300 l/min

Series VR5U08 Nominal Size Inch 1" mm 25 Maximum Flow gpm 80 lpm 300 Maximum Pressure psi 5000 bar 350 Mounting Flange

DN: 0.5 in - 12 in
Pressure: 175 psi
Temperature: 121 °C

... Bell & Gossett, assures optimum system flow balance at minimum pump operating horsepower. Valves can simply be pre-set using the B&G Circuit Setter Balance Valve Calculator, curve booklet G10091, or the ...

DN: 80 mm - 400 mm
Pressure: 0.5 bar - 16 bar

The BERMAD Model IR-450-60-R Level Control Valve with Modulating Horizontal Float is a hydraulically operated, diaphragm actuated control valve. The valve ...

DN: 0.25 in - 1.25 in
Pressure: 0 bar - 350 bar
Temperature: -20 °C - 100 °C

Two or three ways flow regulators, with or without compensated function, unidirectional or bidirectional. Compact design and excelent flow regulation. Flow rate from 1 to 100 l/min. Max working pressure 350 bar. Cartridge style.

DN: 0.25 in
Pressure: 1,000 psi - 5,000 psi
Flow rate: 5 us gal/min

Valves are adjustable: 1,000 to 5,000 psi Features Pressure reducing valves are designed to reduce the maximum pressure in a portion of a hydraulic circuit: the valve ...

Pressure: 30 bar - 240 bar

Kurt PRV-M-02-4 valves are used for controlling system pressure for all subsequent valves based on adjusted pressure. They provide precise control of hydraulic pressure. They are suitable ...

... Robust fabricated construction of carbon steel, with high-performance bronze or stainless steel seats. May be equipped with air vent piping system to avoid cavitation and with by-pass for pressure balancing. Wide range ...

... steel All dredge valves are operated by hydraulic cylinder located on the top of the dredge valve The dredge valve body is stiffened with T-bars The ...

A 3-way relay valve, activated by hydraulic or pneumatic pressure command, opens or closes the main valve. The standard valve is supplied in the "normally ...

Dimensions: DN13 to DN25 body: S355J2G3, stainless steel (1.4571/316Ti) ball + stem: stainless steel (1.4571/316Ti) sealing: plastics Pressure range: up to PN800 or PN700 for stainless steel (note table of dimensions) Field of ...

DN: 6 mm
Pressure: 0 bar - 290 bar

The UZRR6 Pressure-Reducing Valve is size 6, and has a maximum working pressure of 31.5 MPa. Its flow rate reaches up to 50 dm3/min. The valve is designed with a main valve and a pilot ...

DN: 40 mm - 800 mm
Pressure: 10 bar - 100 bar
Temperature: -105 °C - 540 °C

... flanged, weld ends, combination Operating - handwheel, electric actuator, gearbox, remote control, adjusment for pneumatic or hydraulic actuator

DN: 50 mm - 200 mm
Pressure: 125 psi

... required bleeding of trapped air from the diaphragm chamber during installation • Accurate pressure control • Epoxy coated internal and external • One piece, one moving par t diaphragm • In-line service • One pilot ...

DN: 15 mm - 800 mm
Pressure: 16 bar - 420 bar
Temperature: -100 °C - 720 °C

GUIDED SPHERE VALVE METAL SEAT WIDE RANGE The KTN SAT is the best KTN design to solve the widest range of applications. The main goal of this design is its philosophy of achieving the highest security using unmatched ...

DN: 50 mm - 3,000 mm
Pressure: 10 bar - 100 bar

Pressure / flow control valves. Main features : ■ significant reduction in turbulence, vibration and noise ■ fine regulation of the entire range of flow, made possible by the customized trim ■ high precision in ...