I/O

Application range (zones): 1, 2 Ex interface zone: 0, 1, 2, 20, 21, 22 Max. voltage Uo: 24.40 V AT_ST00589: no Highlights - Eight channels can be used individually as inputs or outputs Intrinsically safe Ex ia IIC inputs/outputs ...

The EP1xxx digital input modules are intended for the acquisition of digital/binary signals. Typically, these are mechanical contacts such as break contacts or make contacts, electronic sensors such as inductive proximity switches, optical ...

• Full quality 4K@60p 4:4:4 on a single cable • Rugged modular design • One DisplayPort 1.2 connector • Supports up to 4K60p • HDCP 1.4 Compliant  • EDID support for VESA/CEA, and custom timings • Automatic ...

Input Module IO 113 designed to interface with pump sensors. One without communication as standard variant and one with communication for interface to Sensor Module SM 113

The Astronics 1260-14 Digital I/O Switch Card provides 96 open collector channels in 12 groups of eight bits each. With the open collector version each independent group can utilize a separate internal or external pull-up ...

Hitachi´s newest Remote I/O series provides the best support on future oriented and enhanced application.The strength of this series is the flexibility by gathering machine information within decentralized applications ...

The ESX.iom is a CAN I/O module for 12V and 24V systems, used for expanding the inputs/outputs of a master control unit via CAN. Communication with the master control unit is through CANopen, CANopen Safety, STW protocol ...

Wherever electrical circuits need to be controlled and switched, a relay output module such as the RevPi RO is used. This module makes it easy to switch on and off motors, valves, lighting systems, ventilation systems and other devices. ...

... DAQ board with 8 digital I/O and two 16-bit analog outputs PCI-based 16-channel, 12-bit, 200 kS/s DAQ board with 32 digital I/O and two 12-bit analog outputs PCI-based 64-channel, 16-bit, 100 kS/s DAQ ...

... Modules can be slave stations in LonWorks network consisting of Lonworks compliant products The node can communicate I/O data with other nodes in a distributed network Transmit/receive data quantity can be ...

The Eckelmann I/O system adapts to your application. From simple digital input, to analog modules, to special and safety modules for high-end applications, the UBM I/O system offers everything needed ...

Module with 4 contact outputs for alarm forwarding. The contact outputs are toggle switches (NO / NC). Characteristics • Product type: Datalogger • Logger/module type: Alarm module • Dimensions: 140 x 70 x 60 mm • Material: ...

Up to PLd in accordance with EN ISO 13849-1 and SIL2 in accordance with IEC 61508 Screwless terminals for easy installation Status diagnostics via control outputs and LEDs Number of sensors can be increased to 4 per ...

4-Port x4 PCIe interface to support a total bandwidth of 1GB/s Supports four (PoE4) independent GigE Ports Compliant with IEEE 802.3af Single maximum power consumption 23.5W Internal DC 12V Power Input External DC 19-36V Power Input

Analogue signals are transmitted to the controller or supplied to the peripherals with the highest accuracy and interference immunity. A microcontroller converts the measured values of the analog inputs and outputs with the calibration ...

... • CANopen DS-301 V4.01 application layer A PC board-mounting card for adding I/O to a CAN distributed control network. The CAN-IPM-01 combines configurable digital I/O points with dedicated analog ...

The 8012e Low Profile PCI Express digital interface provides eight optically isolated inputs and eight Reed relay outputs (SPST). The isolated inputs are non-polarized and rated for 3-30 VDC. Optical isolation protects the PC and other ...

The system comprises of 12 relay containing make and brake contacts. It also has 8 transistors for outputs and provides over voltage protection. It has a output current of 24V/2A or 48V/1A with a galvanic isolation of 1500Vrms. The ...

• Expands the alarm panel with 8 high-performance relay switching outputs • Increases the switching power of the 8 additional transistor outputs to auf 8 × 3 A The relay board with 8 outputs is an extension module for the Terxon SX ...

Dedicated I/O expansion modules Various models available to I/O requirements Communications via CAN with Centurion™ controller Type J or K Thermocouples or 100Ω Pt 3-wire RTD temperature measurement ...

Acquisition and actuation module, usable as extension for operator panels with integrated logic ( ATR313, TD329, TD240) or SCADA software. In a standard container DIN43880 9 modules for rail mountain, there are 4 controllers with universal ...

Get multivariable outputs and a powerful configuration and maintenance interface in a convenient, easy-to-install package. This smart module provides fast access to flow, density, temperature and many other parameters. Features ...

... For use with Net2 triggers and actions feature About - The Net2 I/O board consists of 4 inputs and 4 outputs. It connects directly to a LAN/WAN via an onboard RJ45 connector. I/O boards can be distributed ...

... large number of serial I/O ports. Each channel supports RS-232, RS-485, and RS-422 electrical levels to interface to a wide variety of serial communications devices such as modems, data collection equipment, and distributed ...

The Ixxat Safe T100/CS offers device manufacturers an easy way to control safe I/O signals using a safe fieldbus protocol. The module meets the SIL3 safety requirement level as defined by IEC 61508 and Performance Level ...