I/O

... Full-Duplex Distributed Clock1ms Cable typeCAT5 UTP/STP Ethernet cable Surge protection10KV Transmission speed100 Mbps I/O isolation voltage3750Vrms AD Converter Effective resolution16 bits Conversion time~ ...

FEATURES - AD/DA converter module - channels galvanically isolated - 16 analog inputs (16 bit, ±10V, ±5V, ±2V, ±1V) - 250kHz sampling rate - 2 analog outputs (16 bit, ±10V) - integrated RISC controller ASSEMBLE MEASUREMENT CARD. ...

... SBC or MINI-ITX a powerfull I/O capability. The PCIe design can be supported by basic PCI express fpga systems that can include SGDMA. PCIe Device drivers are available for major O.S. The drivers make easy to access ...

Dedicated 6-channel system interface unit for ultra-stable, high precision fluxgate technology DS series current transducers. Powers up to 6 x DS50 to DS2000 at the same time. Supports calibration windings directly from the backpanel Features  ...

PC/104+ VGA card ( PCI bus) XGI Volari Z9s w/32MB DDR2 Resolution 1600x1200 max. , 16M colors VGA or 24-bit TTL

Operating Temperature Range –20~70°C 8 channel analog input (0~5v or 0~20mA) , 12 bit 8-point isolated digit input 5-48 VDC(with SOE), or 8-point single channel counters up to 1 KHz 8-point relay output, 250VAC 5A per point ...

Rack-Based Specialty I/O Over 20 years ago, our direct interface technology was referenced within the Rockwell Automation “Pyramid Solutions Program,” now the “Encompass Program.” Since that time, AMCI has developed ...

MOD I/O* - The new add-on module for the Solar-Log Base The I/O module is the perfect addition to Solar-Log Base, enhancing its capabilities. With the numerous digital inputs and outputs of the I/O ...

... startup message and the module reacts to start node and enter preoperational commands. Special Features CAN-IO Module CIO CAN I/O module for industrial applications 8 digital outputs 24V Analog ...

4 Analogue outputs module. Available in CANBUS or MODBUS RS485 versions. Device able to provide voltage, current signals and current loop, using four different and galvanic insulated channels and power lines. -Input Voltage: ...

... starts via software, timer, or external trigger -Two 16-bit analog outputs; 4kHz update rate -16 high-current digital I/O lines -Alternate micro-fit embedded USB header connector -USB/104 form-factor ...

8 input module for S-bus system, 12Vcc power supply. Power supply 12V= ±10% Absorption: Normal operation 18 Ma All inputs ON 138 mA Communication protocol S-Bus Protection rating IP 30 Operating temp. 0°C .. 40°C Storage ...

Highlights • - 4-Channel 12-Bit Wireless 0-10V Input endNode with USB • - Each Analog Input Includes a Dedicated Non-Shared Ground Input • - For Use with Existing Sensors that Already Include a Power Solution • - Long Range Wireless ...

... infrastructure. The IO-Link device software stack gives sensor and actuator manufacturers a cost efficient and easy way to integrate state-of-the-art IO-Link technology into their products. - IO-Link ...

The LightViper VIM-MY32 YGDAI cards are designed for use with Yamaha™ digital equipment containing YGDAI (Yamaha General Digital Audio Interface) card slots. The VIM-MY32 cards are used in place of the VIM-1832 at the “tail” or mixer ...

... vector memory with per channel dynamic direction control running test rates up to 66 MHz. The PE16S supports programmable I/O levels from -1V ~ +7V per channel. The PE16S offers 16 timing sets, 2 driver TG Edges, 2 ...

... technology is the GRIPLINK controller. It is the bridge between compatible IO-Link field devices and the robot controller. Thus, it is not an ordinary fieldbus master that would forward IO-Link signals ...

... indicator can be equipped with up to 8 I/O. These I/O are electrically isolated, designed for direct connection into PLC†™s and are capable of driving low voltage actuators directly. This module has 8 ...

I/O remote extension modules can provide customers with more choices and more topology.

Include controller modules, digital expansion modules, analog expansion modules, BD signal boards and wireless communication expansion boards, TFT screens, optional accessories and other modules.

Seven Millivolt modules enable the XR440 Data Logger to accept a millivolt signal on channel 3. Three modules (Mvt-11b, Mvt-22b, Mvt-50u) accept a thermocouple (Type J, K, N, R, S, T, B, C, or E). A built-in, precision thermistor on channel ...

... addition to the inputs, our digital IO has a powerful microcontroller that handles the ac­qui­si­tion of the sensors and the CAN protocol. Further­more, security mecha­nis­ms such as guar­ding are fully integrated in ...

... supply high-performance and quality data acquisition modules, which are also called distributed IO modules, IO modules, data acquisition cards, data loggers, and IO cards. FEATURES ...

The DP-CPU computer module connects a workstation with DisplayPort graphic output to a digital matrix switch of the ControlCenter-Compact, ControlCenter-Digital or DVICenter series. Standard variant for the following signals: DisplayPort™ ...