Manual testing devices

The Foam Qualification System FOAMAT® 285 is used by many raw material and foam producers worldwide. It has set quality standards in measuring foam rise profile, foam pressure, foam temperature, dielectric polarization and loss of weight ...

The oil acidity content is an important parameter to check because it determines the refrigerating installation’s good operating condition. The internal chemical processes can alter the oil quality and generate the formation of acids ...

Proven, reliable testing pump for pressure and tightness tests of piping systems and receptacles. Testing and pressure range p ≤ 60 bar/6 MPa/870 psi water, oil, glycol. ph-value of liquids 7-12, temperature ...

... the battery in the device, in a few hours it can be charged completely, you can use it in the charging or after fully charged. Step 2, POWER: Please choose the special test probe head to connect with the DX-201 Measurement ...

Test Equipment for Waveguide Dryers CE certified ISO 9001 Certified The test coffer has proved itself to be a useful tool to check the correct operation of the pressurizer and thus keeping the ...

Contains 5 different filter sheet types for laboratory filtration tests for coarse filtration, fine filtration, clarifying filtration and sterile filtration. A practical and easy-to-use tool to define the right filtration solution at ...

The Oil-in-Water Analysis kit consists of matched quartz cells and a slide-mount holder chosen to match the requirements of the ASTM D7066 method for measurement of extracted hydrocarbon contaminants in water. Key FeaturesO • ...

■ Suitable for measuring the height, thickness, squareness, coaxiality and so on. ■ IP65 protection level ■ High frequence:100 times/s, can measure high speed workpiece ■ Output signal:90°phase difference wave ■ Standard cable length: ...

... diesel/hydraulic/motor compressor drives pressure booster for making high pressure testing medium. The completed equipment consists of power unit pry and pressure testing unit. Standard: • SY/T5053.1～2000 ...

Langry anchor pull out tester is suitable for testing the anchoring force of various anchors, rebars, expansion bolts, and other anchoring components and it can also be used for testing ...

... /T5713,GB/T5714,ISO105E01,E02,E04,AATCC15 etc. Technical parameter 1.Load: 3500cN,(YG631E 10磅)Can order 2.Spring clamping strap: 1500cN 3.Backing plate dimension: 115mm×60mm×1.5mm 4.Packing dimension: 390mm×385mm×260mm Volume: ...

Contact resistance test is testing the resistance to current flow, due to surface conditions and other causes, when contacts are touching one another (in the closed condition of the device). This can ...

optimized for testing large volume components principal application is the test of mufflers and catalytic converter systems as well as ventilation components • flow testings according to volume ...

... Thickness Gauge Testing instrument. It is a well-designed construction used in different production vertical to test the thickness of various ferrous and non-ferrous materials without deforming their actual shape and ...

The Testing Device is installed at a 45 degree angle to the pole facing south. The Testing Device is connected through a cable with the E.S.E Lightning Conductor. The ...

category:Geology / Scissometer brand:PASI item:Mod. S100

... Series Primary Current Injection Tester is suitable for current load test on various circuit breakers, switchgears, CT/PT, primary bus protection and others electric equipment. EPS-PCIT Primary Current Injection Tester ...

... cylinders, two stoppers and tubing. The bath conforms to CE regulation. It is further equipped with a mechanical resettable safety thermostat and a float, to warn the user when the level of the bath fluid has become too ...

... température control: Digital display controller 6. - Accuracy of température control : ±3°C 7. - Electric furnace lift: Manual adjustment 8. - Flask: 250mlMeasuring cylinder: 100ml 9. - Ambient requirements: Température: ...

Transformer Power Tester is an multi-function instrument which is used to test accurately a serious of parameters such as capacity, type, no-load current ,no-load loss, impedance voltage of various transformers. The test ...

Drain test kits for leak test e.g. according to DIN EN 1610 for air and / or water With multi-size plugs several nominal sizes can be checked with one kit only! The extreme flexible ...

ACP portable current transformer test kit designed for analyzing current transformers and voltage transformers of protection or measurement use, which is suitable for laboratory and on-site ...

Measure the amount of color transfer from rubbing. The Crockmeter is a relatively simple rub tester commonly used to determine the amount of color transferred from textile materials to other surfaces by rubbing. ...

Freedom Impact Test Equipment , Impact Laboratory Equipment High Accuracy Pneumatic Control Packaging Drop Test Machine Free Fall Drop Tester Product description ...

1000A Primary Current Injection Tester PCIT-1000 is applied in power system for circuit breaker test, protection system test and current transformer test. 1000A Primary Current Injection Tester PCIT-1000 ...