Soil probe Detecting compacted soil layer and areas left by ploughs The stainless steel soil probe is a tool used for detecting (or probing) soil layer densities, water permeability levels, and ...
... has a built-in temperature sensor for automatic temperature compensation, and supports RS485 Modbus digital output. It is ideal for long-term online environmental water monitoring. Modbus RS485 interface Digital ...
... communication port. Our optical probes contain N36 or N38 magnets and are very well integrated with the meters. You can also use our optical probes with our GSM / GPRS modems and Serial Device Servers. ...
Aktif Enerji Ltd.Co.
The SP2000 sample probes are used for the continuous extraction of gas with high concentrations of particles and temperature or wet processes. They are designed to be easy to set up and maintained. Heating from 0 to 180 ...
... a series of measurement bundles to ease that task. There’s no general optimal interface for spectroscopic measurements; different samples require different interfaces. NLIR has made several different ...
... available in version from 10 to 20 gas outlets; Measurement of gas temperature with thermo measurement of the sample by means of a heated thermo controlled line; Humidity control option: The humidity ...
... provides a rough measurement until the NMR signal can be found. Six standard probes cover a range from the tens of milli-Teslas to the tens of Teslas. The range minimum and maximum values in the following ...
Metrolab Technology SA
Multipurpose type K probe, 1 meter cable with handle
CS87 PROBE OXYGEN SENSOR The CS87™ and CCS 2000™ series of oxygen sensors are designed for measuring the oxygen partial pressure of the furnace atmosphere. The robust design withstands thermal shocks and maximizes ...
United Process Controls GmbH
The enthalpy probe is easy to use and allows simultaneous and precise measurement of plasma enthalpy, temperature, velocity and composition at a given point in the jet flow. It is commonly used in research ...
... reliability of the data even at very low radiation level. Meanwhile, the measurement resuit isn’t influenced by the direction of pollutant source attributed to isotropie electromagnetic field probe. The ...
Coliy Technology GmbH
Probes for coupling with HES spectrometers for Raman observations Our Stand-off Raman probe can make measurements from distances of up to 3 meters from the target. Our Stand-off Raman ...
... shielded) Detection lower Limit: 0.1ug/L(ppb)(20℃) Measurement upper limit: 20mg/l(ppm) Response time: ≤3min(90％, 20℃) Polarization time: >8h Minimum flow rate: 5cm/s; 515 L/h Drift: <3%/month Measurement ...
EIT Solutions Co., Ltd
... field evaluator probe can be used with a digital volt meter (DVM) or oscilloscope to measure AC magnetic field intensities and attenuation ratios. Each probe is carefully calibrated with the calibration ...
Magnetic Shield Corporation
... electrolyte level inside the probe body, this sensor is connected to its electronic inside the probe head;the system generates a local indication (LED) and alarm retransmission in case the electrolyte ...
CLR
... THE AMPLIFIER FOR THE ALCOSENS PROBE The “Transmitter S7” used as measuring amplifier is designed for the connection of one to four probes but can also be extended to any number of probes. ...
Introducing the InfinityXT probe series. InfinityXT enhances and extends FormFactor’s industry-leading Infinity probe family, which has set the benchmark for accuracy and repeatability in the device characterization ...
FORMFACTOR
This glass body conductivity probe, is a traditional two platinum plate electrode design with a nominal cell constant, k = 1 for use with solutions up to about 100 mS/cm. It can be used with either the EP357 Conductivity ...
... electrode design resists sooting and aids in probe burn-off. Burn-Off port as standard with no loss of insertion length Every probe is 100% tested with certification, certificate is shipped with ...
Raman ProbePro product family allows easy and continuous measuring of key process parameters via an optical interface. Raman ProbePro enables time-gated Raman spectrometers to be connected to bioreactors for in-situ, real-time analysis ...
Reflection probe getProbe DR LS NIR diffuse reflectance probe with 2 integrated light sources and a white reference getProbe DR LS is the first intelligent NIR reflectance probe allowing ...
... Change your probe in one touch! According to the application to inspect, you will need a different diameter, length or optics. Rather than a new complete system, schange simply your probe. Moreover, ...
FORT IMAGING SYSTEMS
Use Transmittance Probes to Measure Absorbance Monitoring the Absorbance Inside Containers and Reactors Fully Configurable Spectrometer (Including Interchangeable Slits) Transmittance Probes with ...
Sarspec, Lda
... to give accurate readings the SigmaCheck-2 uses a three-point reference method. The first measurement with the probe in the air and then two further measurements are required which span ...
Ether NDE
Zirkonium-dioxide probe (current probe) for a continuous measuring of oxygen concentration, in a range Lambda > 1 without special gas conditioning, in combustion gases, industry exhaust gases and in oven ...
Lamtec
Please specify:
Help us improve:
remaining