Other clamping elements

Renishaw Equator™ fixturing enables quick and easy fixture set-ups to be created regardless of the size, geometry or material of the part. Modular and custom fixturing for your Equator™ gauging system: Renishaw Equator™ fixtures ...

The Renishaw CMM fixtures range includes a wide choice of standard size base plates and an extensive selection of components with M4, M6 or M8 threaded fittings. Whether you are inspecting parts for aerospace, automotive, electronics, ...

Renishaw's vision fixtures and acrylic base plates allow for back lighting and a clear, clean look at the part from your vision system and multi-sensor machines. Vision fixtures: Renishaw's vision fixtures offer two unique fixturing ...

ZPH pipe clamps are specially designed for the quick and easy instalment of disc nozzles onto pipes. These clamps are very convenient as there’s no need to buy expensive metal tips or welded nozzle tips. You must drill a 19 mm diameter ...

ZPF swivel clamps are specially designed for HGQ, RGN and ZBA series. To install them on pipes all you need is drill a hole, insert the nozzle clamp inside and fasten it with a simple screwdriver. The nozzle clamp body is in PP chemically ...

ZPQ cam and lever clamps are specially designed for HGQ, RGN and ZBA ball nozzles. Only three steps to install them on a pipe: drill a hole, wrap the cam around the pipe and pull the lever down to block it. No need of tools. The body ...

Clamping elements GN 826 are normally used in connection with control knobs and smaller handwheels. Spindles can so be clamped gently and easily and without much construction and installation effort. The clamping wedge stiffens the spindle, ...

With side clamps GN 9190, workpieces are clamped with a pivoted clamping jaw. The clamping force acts laterally and from above to pull down on the workpiece and clamp it against fixed stops and the supporting surface. The clamping ...

Clamping force: 10, 5 kN

Down-thrust clamps GN 9192 are compact clamping elements for quick and secure clamping in tool and fixture construction. Rotating and tightening the clamping screw or the adjustable hand lever moves the clamping arm downwards to clamp ...

Clamping force: 40 N

Pneumatic Pin Holding Clamp is an automated quick fastener with air. Ideal for frequent changeover of tooling, plate and fixture in machinery. Pneumatic Pin Holding Clamp reduces your setup time in semiconductor manufacturing/food processing/pharmaceutical ...

Clamping force: 1,100 N - 3,500 N

Manual swing clamp for quick workpiece setups without using tools. The clamp arm swings into position over the workpiece and clamps straight down just by turning the handle. Spiral cam provides quick clamping with maximum 3500N. Ideal ...

Clamping force: 150 N - 650 N

SPRING SWING CLAMPS Handle clicks at the clamping endpoint. -Feature- ・Turn the handle after the arm swings into position, the cam shaft rotates along the guide pin to push down the arm. The clamping spindle contacts the workpiece ...

UNILOCK clamping module ESA 138 The UNILOCK clamp modules can be mounted in any position, with or without projection on machine tables or as part of fixtures (plates, cubes, towers etc). The UNILOCK clamping module ESA 138 is especially ...

Material: Cone, steel. Balls, ball bearing steel. Version: Cone hardened and ground. Balls embedded in rubber which is vucanised on the cones. Note: In conjunction with the position bushings, the position cones form a centring ...

Centring clamps Material: Body steel. Bushes carbon steel. Version: Black oxidised. Note: These centring clamps allow workpieces to be centred on and clamped in a bore. The clamps have a wide expansion range. The series covers a bore ...

With the Quick•Point® duo2 adapter plate, the smallest centering vise from LANG Technik - the Makro•Grip® 46 micro - can be clamped in a regular Quick•Point® 52 zero point plate. This adapter plate with the dimensions 85 x 85 x 27 mm ...

The new Quick•Point® duo6 grid plate is equipped with 6 zero point mounting holes, which allows a total of 3 possible mounting options. Two Makro•Grip® 46 micro clamped side by side, one Makro•Grip® 46 micro centered or one regular Makro•Grip® ...

The Quick•Point duo2 grid plate is supplied without predefined mounting holes and can be modified in this respect according to needs and requirements. With just 85 x 85 mm, this zero point plate has the smallest footprint of all plates ...

Clamping force: 10 kN - 110 kN

One of our newest low-profile clamp designs posses two jaws with hard tungsten carbide coating These workholding clamps are an excellent choice when: - Clearly visible clamping marks are not allowed in the workpiece but high ...

The function of this unit is simple: the back jaw of a clamp is pushing the plate back, so front jaw of the clamp and a stopper module are clamping the workpiece, It is important to understand the floating fixture principle in general: - ...

Clamping force: 110, 25, 65 kN

The smooth jaw workholding clamps are specifically engineered to securely hold your workpiece without leaving any visible marks or scratches. Our smooth jaw clamps are among OK-VISE’s oldest designs and remain a popular choice due ...

Design: Pneumatic clamping station for setting time-optimised clamping on machine tables with groove spacing of 63, 100 and 125 mm. Fastening is via M12 socket head screws. At least two fitting bores are attached for alignment. The insertion ...

Pneumatic unlocking. Opening operating pressure: K10.3 min. 5 bar. K20.3 min. 4.5 bar. Steel, unhardened. Repeat accuracy < 0.005 mm. Pneumatic clamping station for setting time-optimised clamping on machine tables with groove ...

Perpendicularity: 0.01/200 mm Material: aluminum casting Alignment hole and centre hole: with hardened bushes in accordance with DIN 179 with clamping and base surface Base surface: with hole pattern according to table or drawing, suitable ...

Aluminium clamping block SB 65, with cooling fins clamping diameter 65 mm flange 100 mm height 83 mm

Designed for holding insulated cables and wire. The sample is secured by the cam, which self-tightens as a load is applied and spreads the load evenly. Serrated cams are preferred for materials which may be slippy and so need a 'bite' ...

Fast and safe pipe Alignment Clamping range 8 - 60" Max. wallthickness: 12,7 mm By removing the chain the links und jackbars the chain adjusts to the several pipe diameters Suitable for pipe-pipe, pipe-T-piece, pipe-bend and pipe-flange Our ...

Fast and safe pipe Alignment Clamping range 8 - 60" Max. wallthickness: 12,7 mm By removing the chain the links und jackbars the chain adjusts to the several pipe diameters Suitable for pipe-pipe, pipe-T-piece, pipe-bend and pipe-flange Our ...

PClamp is a modular built system for the secure clamping of rod loads and pneumatic cylinders. It can be adapted to standard systems such as pneumatic cylinders of leading manufacturers (e.g. SMC, Festo) or to individual solutions. Functional ...

Clamping force: 900 N - 2,000 N

Often clamping elements are used only as a transport lock or for the conversion of machines. Hydraulic, pneumatic or electrical models would be oversized for such purposes. Our engineers have therefore designed an inexpensive manual clamping ...

Clamping force: 16 kN - 40 kN

Indipendent and mobile standard sections vises. Extreme versatility and independence Gerardi Modular Elements allow you perfect clamping even of big workpieces which need the heaviest machining using the machine table as surface. Modular ...

Rigid clamp for fixing to all profiles Standard with pivoting Slot nut and screws

Adjustable clamps for fixing to all profiles Standard with pivoting Slot nut and screws

Available for M8-M36 You can use a clamping flange made of nickel-plated steel to connect the shock absorber to the structure more easily. After being fully screwed in, the shock absorber is clamped tightly to the clamping flange, which ...

The SMA model is a self-centering clamping set, which impresses with its high transmission forces. It is equipped with the Easy Open System for easy assembly and disassembly. From 216 to 1‘705 Nm Frictional connection High ...

The PSL-G model is a non-self-centering clamping device. It comes with an Easy Open System, which makes it easy to dismount. Likewise, the model is optionally available with a surface coating. - From 289 to 13‘500 Nm - Frictional ...

The hydraulically-operated bore clamp is particularly suitable for clamping in workpieces with smooth bore holes in the support surface ranging from 8 to 12 mm in diameter. The workpiece is put directly onto the hardened surface of the ...

Clamping force: 1.3 kN

Mini compact clamp Advantages ● Minimum dimensions (Ø 22 mm) ● Partially immersed body ● Space-saving integration by a patented fixing principle ● Housing can be rotated by 360° ● Mounting without pipes ● Workpiece clamping without ...

Clamping force: 2 kN - 22.8 kN

Swing clamps with sturdy swing mechanism Advantages ● 4 sizes available ● Compact design partially recessible ● Very high clamping force already at 70 bar/120 bar ● Sturdy swing mechanism ● Very short clamping time ● Insensitive ...

Clamping force: 2,500 N - 200,000 N

spring activated – hydraulically or pneumatically released hydraulically released Features - Code Clamping Unit - K Standard - E Sizes are available for selection - 032 to 160 Spring activated - F Hydraulically released - H No ...

Clamping force: 1,000, 1,600, 2,500, 4,000, 6,300 N

spring activated – hydraulically or pneumatically released pneumatically released Features - Code Clamping Unit - K Standard - E Sizes are available for selection - 040 to 100 Spring activated - F Pneumatically released - P No ...

centres the hub to the shaft very high transmissible torque Features Centres the shaft to the hub Very high transmissible torques For shaft diameters between 20 mm and 180 mm

Clamping force: 50,000 N

Rail anchors as parking brakes VULKAN rail anchors are used as parking brakes for rail connected equipment used in harsh and windy operating environments. Rail anchors are failsafe brakes with spring operation and hydraulic brake release. ...

Technical data The fast-clamp driving dogs are used to pull the workpiece when it is fixed between two drills. They are highly useful in mass grinding processes. In fact, their high-speed opening and closing allows a significant reduction ...

The permanent clamping magnets MSB are used for clamping of shaped parts and grinding of cemented carbide. Applications - For clamping of shaped parts - For grinding of cemented carbide (type SmCo) Features - Permanently magnetic - ...

The clamping magnets SPM belong to useful accessories for clamping of small parts. Applications - Ideal for grinding and electric discharge machining, measuring and testing jobs - Small magnetic workpieces from 0.5 mm can be clamped Features - ...