Metal nuts

Nominal diameter: 8, 10 mm
Height: 20, 40, 30 mm
Width: 55, 70 mm

Threaded zinc plated steel stud. Material Black thermoplastic, glass fiber reinforced, mat.

Nominal diameter: 5, 8, 6 mm
Height: 18, 20, 19 mm
Width: 34, 48 mm

Brass insert with tapped through hole. Material Black thermoplastic, glass fiber reinforced, mat.

Nominal diameter: 6, 10, 8 mm
Height: 28, 36 mm
Width: 55, 70 mm

Brass insert with tapped through hole. Material Black thermoplastic, glass fiber reinforced, mat.

Nominal diameter: 8 mm - 24 mm
Height: 4 mm - 12 mm
Width: 13 mm - 36 mm

Hexagon Thin Nuts with a fine thread ISO 8675 are used in bolted connections, e.g. as lock nuts to lock components and prevent accidental loosening, turning or shifting. In addition, the nuts ...

Nominal diameter: 5 mm - 10 mm
Height: 24 mm - 36 mm
Width: 48 mm - 70 mm

Design and handling of the wing nuts GN 634 comply with the requirements and claims of the Ergostyle® product family.

Nominal diameter: 5 mm - 8 mm
Height: 11 mm - 18 mm
Width: 15 mm - 30 mm

The surface quality of the knurled nuts GN 530.5 is of a sufficiently high standard to meet the highest requirements. The flash mark is not visible. Duroplast material is highly resistant to chemicals.

Nominal diameter: 5 mm - 10 mm
Height: 24 mm - 35 mm
Width: 50 mm - 75 mm

Only Tapped Hole type is available. -Thread Size- M5×0.8 M6×1 M8×1.25 M10×1.5 -Materials- Body: Stainless steel(SCS13A), Electropolished Datasheet https://www.imao.co.jp/files/on-cat/pdf/en/wk-e.pdf

Toggle Pads (Steel) Steel（S45C） Case hardened(on contact face) Black oxide finish

Nominal diameter: 24, 30, 36, 40 mm
Height: 12, 10, 8, 6 mm

BJ753 / BJ754 Knurled Nuts Material : S45C steel Finish : Black oxide

Nominal diameter: 4 mm - 24 mm
Height: 5 mm - 28 mm

HELICOIL® nuts with integrated HELICOIL® Screwlock ensure secure screw joints. An efficient linking of two fasteners. The nuts comprise a nut body and an integrated HELICOIL® Screwlock ...

Nominal diameter: 6 mm - 20 mm
Height: 7 mm - 30 mm

... SEAL LOCK® sealing nuts provide a reliable seal against gas or liquids, even under high pressure. Easy to install, doubly reliable. SEAL LOCK® seals simultaneously inside the thread and below the head. The one-piece ...

... and unintentional nut loosening. Tool Longevity Other bolting systems put the reaction arm and square drive on opposite sides of the tool causing high stress in the body of the tool, which can lead to failure over time. ...

... Gall Free Nut is the new anti-galling technology in a standard hex nut. The HYTORC Gall Free nut in combination with the HYTORC Washer guarantees the elimination of galled or damaged ...

RIVKLE® blind rivet nuts and studs reliably join thin-walled components. Highly resilient. RIVKLE® creates load-bearing nut and bolt threads on thin walls where cut threads are unsuitable. A range of ...

SEAL LOCK® sealing nuts provide a reliable seal against gas or liquids, even under high pressure. Easy to install, doubly reliable. SEAL LOCK® seals simultaneously inside the thread and below the head. The one-piece ...

Nominal diameter: 3 mm - 20 mm

These captive nuts are press-fit into a clean round hole on the panel to provide permanent retention of the nut. Panels lay over protruding studs and captive nuts are tightened down. Quickly ...

... Riveting Nut Receiving material Brass, Copper, Light Alloy, Stainless Steel, Steel, Thermoplastic, Thermosetting Plastic Assembly Pressure Coating In Natural State, White Zinc Plated Trade name ANCHOR® SELF-CLINCHING ...

... FILTEC-NUT - SELF-LOCKING NUT Filtec-Nut is a symmetric self-locking nut consisting of a FILTEC® self-locking helicoidal insert within a nut, ...

RIVETING NUT Family Threaded rivet bushes Type of product Riveting Nut Receiving material Brass, Copper, Light Alloy, Stainless Steel, Steel, Thermoplastic, Thermosetting Plastic Assembly Pressure Coating In ...

Nominal diameter: 6 mm - 10 mm
Height: 4 mm
Width: 15.5 mm

Channel nuts FOR CHANNELS WITH STRAIGHT FLANGES | OTHER TYPES HEAVY SERIES: For securing of pipe and hose clamps in mounting rails GMV10 + 12, M10, M12 Material: Malleable cast iron, EN-GJMB-350-10 acc. to DIN ...

Nominal diameter: 4 mm - 24 mm
Height: 9.5 mm - 55 mm

Wing nuts DIN 315 | Cast version Radiuses acc. to DIN 315, ergonomically formed, no sharp edges Complete range M4 – M24 available while stocks last On request: Special threads, special parts based on ...

Nominal diameter: 3 mm - 20 mm
Height: 8.8 mm - 31.2 mm
Width: 18.5 mm - 66.5 mm

Wing nuts American form | cold-formed Metric thread from M3 to M20 available while stocks last On request: Inch thread, special parts based on the American form, e.g. with sealing hole Packaging: Standard ...

Nominal diameter: 6, 5, 8 mm

... with just one fastener, the PolyGrip® blind rivet nut has become a fi rst-choice connector in many industrial applications and in trade. PolyGrip® blind rivet nuts – The GESIPA® blind rivet nuts with ...

Blind rivet nut assortment Contents: Each one threaded mandrel M4 and M5 for NTS and NTX. Each 8 blind rivet nuts M4 short and long. Each 8 blind rivet nuts M5 short and long.

Nominal diameter: 8, 5, 6, 4 mm

blind rivet nut G-Sealed Areas of application: G-Sealed can be used in many applications, but is particularly suitable for the automotive industry due to its excellent thermal and chemical resistance. Customer benefits: • ...

Palm grips aluminium, similar to DIN 6335 Material: Aluminium. Grub screw stainless steel 1.4305. Pin stainless steel 1.4310. Version: Vibratory ground or ground and polished. Grub screw and pin bright. On ...

Height: 6 mm - 22 mm
Width: 7 mm - 36 mm

Hexagon nuts with polyamide thread lock high type, DIN 982 Material: Steel or stainless steel (A 2) Version: Galvanised steel. Bright stainless steel. Note: When screwing the nuts ...

Height: 12 mm - 24 mm
Width: 20 mm - 40 mm

Knurled nuts quick-acting Material: Carbon steel. Version: Tempered and black oxidised. Note: Quick-acting knurled nuts are mainly used in applications where no high clamping pressures are required. Tilt ...

Nominal diameter: 4 mm - 8 mm

Material see table Characteristics: it can be inserted sideways into an open groove Tightening torque < 20 Nm

Nominal diameter: 4 mm - 8 mm

Material Class 8 steel Characteristics: it can be inserted sideways into an open groove; positioning spring for fitting in vertical grooves Tightening torque < 20 Nm

Nominal diameter: 12 mm - 120 mm

Ready-to-install Red Bronze Flange Nnut TGM-EFM: Red brass flange nut TGM-EFM for movement drives with particularly favourable wear characteristics.EFMs can be mounted using the KON, KKA, MAFN, and KAR adapters.Material: ...

Nominal diameter: 10 mm - 80 mm

Thanks to the material used, the long red bronze nut TGM-LRM is characterised by particularly low wear. The outer diameter is generously dimensioned for individual further processing.

Nominal diameter: 6 mm - 90 mm
Height: 8 mm - 20 mm
Width: 16 mm - 120 mm

This is a securable grooved nut that is secured by two radial brass pins. Self-locking grooved nut with polyamide ring. Secured by a polyamide ring – usable up to max. 100° C. Material (strength ...

Nut to be used in conjunction with a hammer head screw Measures: M6 / M8 Material: Zinc plated steel / stainless steel

Nominal diameter: 6 mm
Height: 25.8 mm - 31.7 mm
Width: 9.8 mm

Split Blind Rivet Nuts "GO-SPLIT" Pre-slotted, Flat Head, Round Shank Slotted, Open Type, Steel Zinc Plated Packaging - Goebel Clamping range min. - 7,1 Length (mm) - 31,7 ø - 9,8

Nominal diameter: 10 mm

Blind Rivet Nuts "GO-NUT" Flat Head, Round Shank Knurled, with Serration under Head, Closed Type, Stainless Steel A2 Clamping range max. - 6,0 Packaging - Goebel Clamping range min. ...

Nominal diameter: 10 mm

Blind Rivet Nuts "GO-NUT" Flat Head, Round Shank Knurled, with Serration under Head, Open Type, Stainless Steel A2 Clamping range max. - 6,0 Packaging - Goebel Clamping range min. ...

Nuts made of molybdenum and the molybdenum alloy TZM are available in the Plansee Online Shop. Order fast and easily from the producer's online shop: www.plansee.com/shop

Nominal diameter: 4 mm - 10 mm
Height: 13 mm - 28.5 mm
Width: 16 mm - 32 mm

Nominal diameter: 4 mm - 10 mm
Height: 14 mm - 22.5 mm
Width: 19 mm - 36 mm

Height: 9 mm - 22 mm

Slide quick-action clamping nut directly over screw thread up to clamping point and then lock it. If the quick-action clamping nut base is firmly in contact at the clamping point, then the head can be ...

Nominal diameter: 12, 16, 20, 25 mm

Ball screw nut Ø12, 16, 20, 25 mm with single-path return for average use Round nut for clamping block 1 (base securing) and clamping block 2 (flange securing) Nut pitches: ...

Nominal diameter: 16, 20, 25 mm

Ball screw nuts Ø16, Ø20, Ø25 mm with complete ball return -for high loads -pitch: 20 mm and 40 mm FEATURES: -material 16MnCr5, sharpened -version as round nut or flange nut ...

Nominal diameter: 4 mm - 10 mm

ITCA2-Rivsert Stainless steel A2 h.7,0 gr0,5-3,0 D M5/030 A2 stainless steel. Open cylindrical shank. Dome head.

Steel class 6 nut. Steel C67S cage. Cage nuts, thanks to their fins, can create female threadings on pre-drilled sheet metal, already having square, rectangular or round holes.

Steel class 6 nut. Stainless steel X5 Cr Ni18/10 cage. Cage nuts, thanks to their fins, can create female threadings on pre-drilled sheet metal, already having square, ...

Height: 2, 10, 4 mm
Width: 40 mm - 600 mm

... different types of nuts actuated by grease: • Nuts with transverse or axial nipple and release screw. Nuts are actuated by an external unit (normally a grease pump). • Nuts ...

Nominal diameter: 6 mm - 16 mm
Height: 9.5 mm - 22 mm

SELF-BREAKING LOCK NUT - STAINLESS STEEL A2 INOX A2

The classic form of blind rivet nuts with parallel shank for use in dry and grease-free components . The availability in aluminum, steel and stainless steel with all head shapes (flat head, countersunk ...

Nominal diameter: 6, 8, 10 mm
Height: 18, 19, 22 mm

The HONSEL RIVET NUT "headless" can be used in existing and new applications. The blind rivet nut can be flush mounted in smooth bores without countersinking. The omission of the "countersink" process ...

Self-clinching rivet nuts from series 10.455 and 10.456 are riveted into the component. A shaft is passed through a pre-punched hole in the component and riveted on the opposite side. The base material is not deformed ...

Nominal diameter: 19, 25, 22 mm

... Locking T-Nuts or Pronged Tee Nuts as they are also known, are manufactured from a high performance zinc plated steel, which provides an excellent level of resistance and strength across medium to heavy ...

Nominal diameter: 12, 14.5 mm

All of our Cone Shaped E-Nuts are manufactured using a silver zinc alloy, which provides an extremely strong and durable solution capable of a number of different uses. Threaded E-Nuts are ideal for a ...

Nominal diameter: 7.8 mm - 16 mm

... Features:Metal Threaded D-Nuts for wood M4 - M10 line drawing Manufactured from a high quality Zinc Alloy Perfect for use as wood furniture inserts Available in thread sizes M4 - ...