- Electricity - Electronics >
- Electronic Component >
- Preamplifier
Preamplifiers
Frequency: 40 kHz - 45,000 kHz
The LEGION AMP is a high channel count, compact footprint preamplifier for integration with third party analog-to-digital converters; Boosting detection of small signals by +40 dB while minimizing background noise (high ...
Suitable for: HF59B, HFE59B Increases the sensitivity of the HF-analyser by a factor of 10 (= 10 dB), that is nominal 0.001 µW/m²*. Adaptor plug to be connected to the antenna input socket, remote-fed by the respective basic device. ...
Voltage: 450 mV
Frequency: 3 kHz - 2,000 kHz
... difficult operating conditions. The AEP5 as well as AEP5H is a general purpose preamplifier supporting single-ended sensors. This preamplifier is a wide-band preamplifier available ...
Voltage: 17 V - 25 V
Current: 4 mA
The MV:220A 1/2-inch Preamplifier is a general purpose preamplifier suitable for use with prepolarised microphone capsules. It is a small unit with a slimline profile and is powered via the coaxial ...
Frequency: 0 Hz - 130,000 Hz
... capacitive sensors Temperature, deformation, pressure, force, acceleration, displacement... DESCRIPTION The EPC1-D preamplifier is characterized primarily by its low noise level, high input impedance and gain accuracy. ...
The single-channel preamplifi er is used for signal transmission between a dispensing valve with pressure sensor and a downstream Loctite controller 97152 or 97153. The amplifying factor is adjusted depending on the viscosity of the product ...
Frequency: 1 MHz - 15 MHz
... unit is a high-performance remote pulser/preamplifier dedicated to TOFD inspections and compatible with the Olympus scanner line as well as PV-100 and PV-200 weld-inspection systems. This remote pulser/preamplifier ...
Frequency: 550 kHz - 30,000 kHz
The PR-06-04 is a four-channel pulser/preamplifier for pulse-echo. Each channel can drive a conventional UT probe for a higher gain pulse and boost the return signal, thereby improving detection and signal-to-noise ratio. The ...
Voltage: 10 V - 28 V
Current: 65, 30, 200 mA
Frequency: 50 Hz
... precise and accurate flow and volume measurements with as high a resolution as possible, VSE has developed the optional VSI pre-amplifier. The integrated electronics of the VSI produces greatly improved signal quality ...
Frequency: 100 MHz - 6,000 MHz
Works with any brand of Spectrum Analyzers and directly fits to any SPECTRAN Spectrum Analyzer. Broadband sensitivity increase by up to 23dB. The UBBV 1060 BPA is a low-noise, pass-through amplifier offering industry-leading performance ...
Frequency: 20 GHz
... SPECTRAN V5 unit. Made in Germany: All UBBV DC20 Preamplifier are developed, individually produced and calibrated in Germany at the Aaronia factory. Included in delivery: All UBBV DC20 Preamplifier ...
Frequency: 9 kHz - 6,000,000 kHz
High-End ultra low noise RF Preamplifier up to 6GHz. A "must have" for EMC measurements Extremely low noise Amplification of very weak signals Boosts any antennas gain Compensation of negative antenna gain Works ...
Walchem Preamplifiers offer a way to use any standard non-amplified pH/ORP/ISE electrode with our controllers. Once amplified, the signal may be extended up to 1000 feet (305 meters) using 22 AWG cable. For long cable ...
Your suggestions for improvement:
Receive updates on this section every two weeks.
Please refer to our Privacy Policy for details on how DirectIndustry processes your personal data.
- Brand list
- Manufacturer account
- Buyer account
- Our services
- Newsletter subscription
- About VirtualExpo Group
Please specify:
Help us improve:
remaining