Serial converters

... connecting the converter to built-in RS-232C port of the CS/CJ series and the RS-232C connector of the Serial Communications Units (D-Sub,9-pin). • Up to 9 nodes can be linked via built-in RS-232C ...

... select and configure the right media converter for your requirements. The RUGGEDCOM RMC series of Ethernet and serial media converters are compact devices designed to bridge the gap ...

Step Towards IoT A multi-converter that offers a solution for data collection, connecting to a wide variety of equipment as well as PLC.

The EDW-100 is a serial to Ethernet converter designed to allow RS-232, RS-422 and RS-485 serial devices to communicate via TCP/IP Ethernet networks. DIP switches are used for configuration ...

... ports, therefore conversion to RS485 is necessary. The 9D-485 module is a simple non-isolated two wire half duplex RS485 converter which fits into any PC based system. This port powered two-channel module converts the ...

The CS5302P is part of a new series of pro audio converters aimed at providing the most transparent audio conversion within one device that is simple to use and integrate. The CS5302P is a high-performance, 32-bit resolution, ...

The USB serial converter (USB to RS422/485) allows you to add a serial interface to embedded systems by Syslogic or third parties. The serial interface ...

H0FL-0135 V.35/E1 converter transports V.35 data via E1 network. It's widely used for routerinter connection and DDN accessing as well as remote LAN connection. It can provide best solution with simplicity, efficiency ...

... measurement and outputs simulation Options: » Hart signal transparency with the barrier » RS232 programming cable and USB / RS232 converter EC Type examination certificate number : LCIE03 ATEX 6469X ATEX ...

... Rail Converter Ethernet Direct offers industrial grade media converters serial converters and device to allow devices with different serial interfaces ...

... 3-in-1 RS232/422/485 to serial fiber media converter Easy DIP switch configuration to change serial modes Serial to fiber media converters supports ...

Interface Converter Transfer SEL Mirrored Bits communications via an IEEE C37.94 fiber-optic link through a communications multiplexer. Or, convert other EIA-232 serial links to IEEE C37.94 optical fiber ...

... conventional copper serial cables. Transition Networks’ Just Convert It serial RS232 to Fiber Media Converter is an inexpensive, no frills way to extend the distance between serial ...

... the M-Bus interface in their counters, making it the ideal basis for remote reading applications. Our M-Bus Master (M-Bus converter) is universal and simple M-Bus Master that can be connected up to 250 M-Bus devices. ...

The Fiber optic converter by eks comprises of a RS232 interface and a system of DL-232. The DL-232 controls the communication within the system through the use software handshake. The whole unit features its advanced ...

IF-6000 – USB to RS232-422-485 interface High speed isolated USB to RS232-422-485 interface. The IF-6000 module is a cost effective way to convert RS485 industrial buses to a USB ...

... or by email contact@aecl.com.tw Aecl AUS-405 RS485/RS232 to LoRa Converter *Support Modbus RTU protocol. *Not Support LoRaWan protocol. AUS-405 RS485/RS232 to LoRa Converter is the media for ...

The DM-232TO485 communication line converter is available for 35 mm rail mounting. The converter supports both automated and controlled switching of transfer direction with maximum transmission rate of ...

External MODBUS over RS485 adaptor for UPS and STS • For SCADA and BMS connection • MODBUS RTU protocol • 2 wire RS485 output • 8 bit hardware addressable

... well. The MultiTC has the following features: The MultiTC provides an easy way to power the sensors, either through the USB port of a laptop and the wylerCONNECT, or via a separate 24V power supply. Forwarding ...

TTL and LVTTL to RS232 Interface converter from TTL and LVTTL to RS232

... The STS-1915S is equipped with a standard DB9 female connector and serial terminal block for flexible wiring. The serial converter can be either powered by the RS-232 line voltage or ...

The T610_C is a built-in module for interfacing Modbus or HART transmitters to a FOUNDATION Fieldbus network There are options for using RS485, RS232 or pure CMOS UART communication. Fint provides drivers with HART Master or Modbus ...

... optic converters of the TR-55 series enable the connection of devices equipped with an interface compliant with the RS-232 / C, RS-422 and RS-485 recommendations with the use of a single-mode or multi-mode fiber line. Depending ...