Shaft seals

Fluorten PTFE rotary shaft seals are made using the most advanced technologies, with the seal lip preloaded radially using a special thermal moulding process. To avoid leaks and for a ...

Temperature limit: -30 °C - 220 °C
Pressure limit: 0.5 bar - 600 bar
Diameter: 10 mm - 2,500 mm

Our range includes: • rotary shaft seals • vee-packing sets in cotton fabric NBR • sealing systems for hydraulic cylinders • flat gaskets in many materials • o-rings • packings and braided ...

Temperature limit: -30 °C - 200 °C

... the radial and axial sealing of flanges, sleeves and covers (static application) and for sealing of pistons and rod seals, rotating shafts and helical movements (dynamic). They are often used for quasi-static ...

Temperature limit: -100 °C - 250 °C

... complicated mechanical face type seals. PTFE lips seal provides the designer a significant improvement in performance over elastomer lips seals at a much lower cost than the mechanical ...

Temperature limit: -160 °C - 260 °C
Speed: 1 m/s - 15 m/s

stripsguide Tapes The function of a hydraulic wear ring is to guide the shaft and hole sealing of a hydraulic cylinder, absorbing transverse forces. At the same time, it prevents metal-to-metal contact, optimizing ...

The V-Ring an elastomer axial seal for shaft bearings. It seals axially against a conterface. This type of seal has been used widely for several applications and has ...

Diameter: 35 mm
Outer diameter: 50 mm

Oil seals prevent internal system fluids from leaking and keep external contamination from entering the system. Leakage and/ or contaminants paths occur between the shaft and the seal ...

Temperature limit: 260 °C
Diameter: 8 mm - 30 mm

The High-Performance Shaft Seal The thermoelastic high-performance seal Multi-Seal is an alternative for mechanical seals and braided packings. The ...

Technetics Group Brush Seals – Designed to increase airflow efficiency in engines and compressors Replacing labyrinth seals with brush seals from Technetics Group can reduce leakage ...

Temperature limit: 400 °F
Diameter: 3 mm - 8 mm
Outer diameter: 4.7 mm - 11.4 mm

... is molded slightly smaller than the shaft size so that an interference fit is achieved. It is this tight fit that seals the shaft, which stops material from migrating past, and drives ...

Temperature limit: -90 °C - 260 °C
Pressure limit: 0 Pa - 1,500,000 Pa
Diameter: 8 mm - 1,200 mm

... General purpose rotary shaft seal. idéal for heighlimits to 5 mm•Suitable for unhardened sharfts as well•Typical Applications: Compressors, Pumps. MixersActuators. Blowers. Strirnng Systems . Fltting ...

Features 1/4" shaft versions house two ball bearings that support the shaft of the o-ring seal for the smooth, low-torque operation usually found only in expensive motion feedthroughs Bronze ...

... manufactures a wide variety of components, which includes static seals. The static seals are available in four models such as unsplit, split, envelopes and as well as O-rings. A static seal ...

... to prevent leaks, and minimum friction and wear. Repack-S seal designs achieve this. They provide a leak free barrier between moving and stationary surfaces in applications such as rotating shafts and ...

Temperature limit: 248 °C
Pressure limit: 0 psi - 1,160 psi

Typical uses: pump packing / valve stem seals Temperature: 120°C (248°F) Max Pressure: 8 MPa (1160 psi) Max Shaft Speed: 5 m/s (980 fpm) pH Limits: 6-9

Diameter: 35 mm - 160 mm

... complete kit and comprise a seal carrier with an integral rotary shaft seal, a gasket and hexagonal socket cap screws for fixing the carrier to the central washer of the bearing.

Temperature limit: -40 °C - 220 °C
Diameter: 40 mm - 160 mm

... and eliminates the requirement of not only a barrier-fluid but also any chances of seal-face contamination into the product. The specially developed system between the shaft protection sleeve and the ...