Signal amplifiers

The DCI-Eco is the latest member to its DCI product family. MPB’s DCI-Eco Optical Line System (OLS) is a complete DWDM line system for data center interconnect applications. It provides all of the optical grooming necessary for transmission ...

Voltage: 220 V
Frequency: 75 Hz

The R-RF-10-RZ amplifier is a desktop amplifier explicitly designed for RZ code transmission in high-speed optical fiber communication systems. It amplifies tiny high-speed signal levels ...

Voltage: 1.5 V - 15 V
Current: 1,000 mA
Frequency: 600 MHz - 940 MHz

Frequency: 100 kHz - 80,000 kHz

... which has a signal level above a threshold set as desired. The switch can also be activated by remote control provided to the device via RS-232 serial connection or through entrance Dry-Contact (TLC). Each output is ...

Voltage: 220, 110 V
Power: 20 W

... impact-resistant, dustproof, moisture-proof 20 watt amplifier Overload protection with current limiting and thermal shutdown circuits Modular PCB Fuse protection for power supply and speaker amplifier Surge ...

... this module also improves OSNR (Optical Signal to Noise Ratio). The MICROSENS Raman offers a maximum output power of 28.5 dBm. The amplifier includes an automatic eye safety mechanism that shuts down ...

Voltage: 1.8 V

The PI2MEQX2503 provides two lanes and clock MIPI D-PHY ReDriver™ with regenerates the D-PHY signaling. The device complies with MIPI D-PHY1.2 standard and can be used in either a MIPI CSI-2 or MIPI DSI application at datarates of up ...

... 85mm*114mm*46mm - Amplifying service time: 8-10hours N.W.: 282g - Product color: Black/Blue/ Red Battery capacity: 1800mAh Signal range: 15meters - Appearance technolgy: ABS Bluetooth version: 4.2 - Format support: ...

Voltage: 8 V

Erbium-doped fiber amplifier module is the professional CATV equipment which is used for amplifying optical signal then transmission in the CATV transmission system. The EDFA module is compact and light ...

Voltage: 12 V - 14 V
Power: 100, 150 W

... total, which have ascending delay times. So not only linear amplifiers but other devices, like transverters, can be switched on with defined times. The DCW 2004 B is designed for the amplifiers ...

Voltage: 230 V
Power: 240, 120 W
Frequency: 80 Hz - 16,000 Hz

... places with PA system that require multi-channel high-power digital power amplifiers. Feature: * 120W/240W constant impedance and voltage high performance digital power amplifier (4-16Ω/100V) with 2/4 ...

Voltage: 100 mV - 15,000 mV
Frequency: 10 Hz - 100,000 Hz

... output signals • Output offset controls • Output time constants from 100 µs to 30 s • 1F and 2F reference signal operation • 90° step and fine phase control Lock-in amplifiers ...

Voltage: 3.3 V
Current: 5.6 mA
Frequency: 22 GHz - 29 GHz

... it particularly suitable for use in wideband radar applications as well as for signal amplification in k-band wireless RF communication systems. The low-noise amplifier chip features a gain control ...

Power: 4 W
Frequency: 4 GHz

... antenna ● RFID reader,active tag,antenna ● Small & mini repeater,LTE home repeater ● Phase shifter / Attenuator ● Balanced amplifier / LNA configurations ● Modulators ● Mixers ● Power combining /dividing

Power: 3, 9 kW

The 5CX1500A is designed for use as a Class C rf power amplifier in radio frequency applications. For FM broadcast service, the 5CX1500B is recommended in place of the 5CX1500A, for improved reliability.

Voltage: 110, 220 V
Current: 100, 1 mA
Frequency: 50, 60 Hz

Voltage: 30 V
Current: 10 A
Frequency: 2 Hz - 20,000 Hz

... power amplifier designed to work with electrodynamic shakers in the lab or in production. The nominal output power of the amplifier is 200 VA. Digital amplifier RL-A200 is distinguished ...

The PC-505B is the lowest noise, switchable resistive-feedback patch clamp amplifier available. This new model also has features of particular interest to those doing whole cell studies. The slow capacitance compensation ...

Avago Technologies offers a broad selection of rf and microwave amplifiers including Power Amplifiers (PAs), Gain Blocks/Drivers, Low Noise Amplifiers (LNAs) and variable gain amplifiers ...

Frequency: 1,000 Hz - 60,000,000 Hz

... lock-in amplifier is a device used for weak signal detection. Weak signals are often submerged in various noises. The lock-in amplifier can extract the weak signal ...

Voltage: 27 V
Current: 2.4 mA

Straingauge Amplifiers Single and multi-channel Straingauge Amplifiers with precise, low-noise standard analogue outputs, display and setpoints for industrial applications. These accelerometers ...

Power: 3,000 W
Frequency: 10 kHz - 100,000 kHz

ETS-Lindgrens Model 8000-08 RF Power Amplifier is a 3000 W power amplifier, designed primarily for EMC applications that include MIL-STD 461 RS103, 200 V/m. Utilizing GaAs technology, this RF amplifier ...

Voltage: 300 V
Current: 1.5, 2 A

... power booster amplifier designed to provide voltage and current gain for a small signal, general purpose operational amplifier. By using the PB51 power booster within the feedback loop ...

GLSUN OTS3000-EDFA Erbium Doped Fiber Amplifier is different from OEO and can directly amplify the signal of multi-wavelength from the C-band to effectively extend the transmission distance when the optical ...

Voltage: 5, 10 V
Current: 10 mA

Analog amplifier card for variable speed drives. Overview The analog amplifier card converts the angle of handle deflection into a voltage reference signal. The signal ...