{{product.productLabel}} {{product.model}}
{{#if product.featureValues}}{{product.productPrice.formattedPrice}} {{#if product.productPrice.priceType === "PRICE_RANGE" }} - {{product.productPrice.formattedPriceMax}} {{/if}}
{{#each product.specData:i}}
{{name}}: {{value}}
{{#i!=(product.specData.length-1)}}
{{/end}}
{{/each}}
{{{product.idpText}}}
{{product.productLabel}} {{product.model}}
{{#if product.featureValues}}{{product.productPrice.formattedPrice}} {{#if product.productPrice.priceType === "PRICE_RANGE" }} - {{product.productPrice.formattedPriceMax}} {{/if}}
{{#each product.specData:i}}
{{name}}: {{value}}
{{#i!=(product.specData.length-1)}}
{{/end}}
{{/each}}
{{{product.idpText}}}
... spatula or similar to apply a sufficient amount of paste to the head or nut contact surface and to the thread. Spray on evenly OKS 241 spray. The paste will also act ...
OKS Spezialschmierstoffe GmbH
... spatula or similar to apply evenly a suitable quantity of paste to the head or nut contact surface and to the thread. The paste also acts as a sealant against spray water and condensate. ...
OKS Spezialschmierstoffe GmbH
... wire brush) and then with OKS 2610/OKS 2611 universal cleaning agent. Evenly spray a sufficient amount of OKS 2351 onto the head or nut contact surface and thread. Do not use paste instead of grease and ...
OKS Spezialschmierstoffe GmbH
... lubricants from the thread and sliding surfaces. Evenly spray a sufficient amount of OKS 2501 onto the head or nut contact surface and thread. The paste will also act as a sealant. Caution: Do not use ...
OKS Spezialschmierstoffe GmbH
ANTI-SEIZE ALUMINIUM PASTE GREASE FOR VERY HIGH TEMPERATURES ASSEMBLY, INSTALLATION, REMOVAL ENABLES RESOLUTION OF PITTING PROBLEMS COMPLIES WITH SPECIFICATIONS MIL A 907 ED - STM 7411 A SECLF 216 - MIL A 907 E 80
... cartridge using the required pump. With the Airless system, spray horizontally at 20 to 30 cm from the surface. Recommended tips 527 to 531, pressure 140-150 bar. After an initial vertical spray application ...
Sofec
... weather, mix the product rapidly to make suction easier. We recommend that the filters are removed from the pump and that spraying is done atabout 80 cm from the surface. After spraying, smooth down carefully using ...
Sofec
... Procedure: We recommend removing the filter pump and spray about 80 cm from the support. After spraying, smooth carefully using a 60 cm blade. Tip: When Forged, keep a closed angle. Tools: Airless Spray ...
Sofec
... Procedure: We recommend removing the filter pump and spray about 80 cm from the support. After spraying, smooth carefully using a 60 cm blade. Tip: When Forged, keep a closed angle. Tools: Airless Spray ...
Sofec
... 59.1: clean, dry and in good condition (humidity between 6 and 16%). In cold conditions, mix the product. We recommend spraying without filters, about 60 cm away from the surface.
Sofec
... to16% moisture). In cold weather, quickly mix the product to facilitate the aspiration. We recommend removing filters and spray about 60 cm support.
Sofec
... suction easier. Airliet G30 plaster filler can be sprayed with any type of render spray machine, in two coats. We recommend to remove the filter from the pump and to spray at about 60 cm from the substrate.
Sofec
... Ideal tips are 641 and higher, depending on the machine power. • Spray at around 60 cm from the surface. Do not use a filter. • It is advisable to use protective eyewear when spraying to prevent small ...
Sofec
... apply this method: 1) Spray a first coat of filler of around 300-400 g/m², which will reveal imperfections and serve as an undercoat. 2) Then, carefully smooth the surface. 3) After drying, sand and remove any dust. 4) ...
Sofec
... composition, BrazeTec nickel-based brazing pastes can be applied in a variety of ways: Screen-printing Spray Immersion Roller-coating Using dispensers or syringes Nickel-based brazing ...
Please specify:
Help us improve:
remaining