- Hydraulics - Pneumatics >
- Valve >
- Vacuum valve
Vacuum valves
... Electric Ultra-High Vacuum Gate Valve Applicable range (Pa) - 105~1.3×10-7 Gas leakage rate (Pa.L/S) - ≤1.3×10-7 ≤1.3×10-7 Valve”s roasting temperature(℃) - ≤150(Except the drive ...
Shanghai EVP Vacuum Technology Co., LTD
DN: 20 mm - 25 mm
Pressure: 13 bar
Temperature: -30 °C - 80 °C
... quickl valve can be installed in the piping and some important position such as outlet of compressor and upstream of pneumatic tools .Good for the separation ,adjustment and maintenance . Quick install . Provide ...
Zhejiang Compressed Fluid Transmission Engineering Co.,Ltd
... spring-loaded check valve is extremely efficient. There is also a built-in vacuum valve to arrange air outflow and vacuum discharge when the flow stops, and also low ...
DN: 0.375 in - 2 in
Pressure: 0 bar - 10 bar
Temperature: -20 °C - 150 °C
Pneumatically operated blocking valves - VNC-VDA series The pneumatically operated blocking valve provides the opening/closing function and the automation of this function in a single, space-saving ...
SENGA
DN: 150 mm - 500 mm
Pressure: 0 bar - 6 bar
Temperature: -20 °C - 240 °C
Pressure tight locking valve for pressure-/vacuum-hoppers, pipelines or reactors, free passage when open, shutting disc is not leaving the housing when open/close position. Pressure-tight seal for ...
HOSOKAWA SOLIDS, S.L.
DN: 700 mm - 1,200 mm
Temperature: -200 °C - 600 °C
... and lower piping stress Neldisc triple eccentric disc valves operate both in control and shut-off applications. Compact and light weight construction with Neles B-series actuator Suitable for vacuum ...
Neles
DN: 50 mm - 300 mm
Gas approved high performance wafer butterfly valve. Liner in gas approved NBR rubber, vulcanized on back-up ring. Suitable for vacuum. ATEX - DVGW - SIL
Dansk Ventil Center A/S
DN: 0.125 in
Pressure: 0 bar - 400 bar
Mini Needle Valve, Tradinco T1700 Special instrumentation-needle valve for vacuum and pneumatic pressures up to 400 bar. Excellent feel and low torque allows high ...
Pressure: 0 psi - 125 psi
Temperature: -20 °F - 180 °F
TAC Manual Valves are miniature pneumatic 2, 3 and 4-way Push Button and Toggle valves available in 10-32 UNF, 1/8 and 1/4 PIPE sizes. Compact and rugged, TAC valves provide excellent ...
DN: 10 mm - 80 mm
Pressure: 40 bar - 100 bar
Temperature: -20 °C - 150 °C
... yellow. • TESTED FOR VACUUM: (800 mbar). • Art. 2”1/2 - 3”: with locking device and mounting plate ISO 5211 GENERAL APPLICATIONS: ON-OFF valve for: chemical products, for water and pneumatic ...
... venturi, burner control and, of course, the gas valve. Our gas valve range is suitable for the natural and liquid gases used in gas heating technology. This also applies to hydrogen. All our gas ...
Pressure: 0 bar - 15 bar
Required to control vacuum for Hei-VAP Control models with valve-controlled vacuum pumps. Can be positioned for easy access and cleaning. Not required for manual vacuum control
DN: 0.5, 1, 1.5, 1.8 m
Temperature: 150, 180 °C
... injection valve ensures straightforward isolation of the mould cavity and vacuum tight sealing, ensuring reliable and clean operation • Careful positioning of the material port allows use in deep ...
PILOT CONTROLLED SAFETY VALVE Applications Maintain the vacuum in case of a venturi or pump stopping
SAPELEM
DN: 6, 8, 12, 20 mm
Temperature: -40 °C - 60 °C
... Feature of CV Self-Sealing Valve Self-sealing: If the device or connector is removed, self-sealing can be done It can be used repeatedly Can be used on outdoor switching devices SF6 gas inflation and ...
Temperature: 60 °C - 302 °C
VACUUM VALVE SERIES ULVAC, Inc.’s vacuum valve employs the vacuum technology of the vacuum specialized manufacturer accumulated through ...
... relief and check valves for since the time of the Apollo and Gemini programs and more recently for the International Space Station and the Orion Spacecraft. Our pressure relief valves are suited for ...
DN: 8 mm - 18 mm
Pressure: 29 psi - 140 psi
Temperature: 130 °C
Air Valves reliably break the vacuum created when molding deep draw parts, such as containers and buckets. Specifications:• Pressure Required: 29-140 psi• Maximum Mold Temperature: 265 ̊F (130 ̊ C
Your suggestions for improvement:
Receive updates on this section every two weeks.
Please refer to our Privacy Policy for details on how DirectIndustry processes your personal data.
- Brand list
- Manufacturer account
- Buyer account
- Our services
- Newsletter subscription
- About VirtualExpo Group
Please specify:
Help us improve:
remaining