Flow rate: 100, 300, 600 l/min
... large flow rate, 3-stage diffuser construction ejector Energy saving function selectable, with reduction of up to 90% Suction flow rate up to 600 l/min, increased by 250% compared to one-stage ejectors Supply ...
SMC
... range of ejector types from one source: Heavy duty ejectors are required for harsh operating conditions. Compact ejectors require little space with a broad scope of functions. Inline ...
Ultimate vacuum: -90,000 Pa - -73,000 Pa
Weight: 15 g - 84 g
• Two- or three-stage cartridges with extremely compact dimensions • Can be integrated near the gripping point, lightweight • Available in the cartridge-only or cartridge with holder and integrated silencer versions
Ultimate vacuum: -90,000 Pa - -73,000 Pa
Weight: 2.4 g - 19 g
• Two- or three-stage cartridges with compact dimensions • Can be integrated near the gripping point, lightweight • Available in the cartridge-only or cartridge with holder and integrated silencer versions
• Two-stage cartridges with extremely compact dimensions • Can be integrated near the gripping point, lightweight • Available in the cartridge-only or cartridge with holder versions
Ultimate vacuum: 4.5, 5 bar
Flow rate: 161, 23, 65 l/min
► Special features: Complete solution for easiest installation Integrated valve technology and vacuum monitoring Wide range of outputs Normally open suction valve Electronic vacuum switch (KE15NOE) Digital vacuum switch (KE15NOD, KE25NOD)
Ultimate vacuum: -0.8 bar
Special features Integrated vacuum connection Vacuum (bar) -0.8 Compressed air connection
External Venturi vacuum generator, up to -800 mbar with bypass valve. The pneumatic module MAV100 is a generator of negative pressures fully integrated and incorporates a system of valves to switch from positive to ...
Variable - Flow Ejectors are based on proven GEA jet pump technology and often used for heat recovery. Upgrading of waste steam / low-pressure steam Heating of evaporators Heating recovery from hot condensate Mode ...
Flow rate: 21 ft³/min
... range of vacuum ejectors including basic ejectors, basic ejectors with an electro-mechanical switch,inline ejectors, ejectors including ...
Parker Pneumatic Division Europe
Ultimate vacuum: 5 bar
Flow rate: 0.84 m³/h
Operating temperature: -10 °C - 80 °C
Specification: customized Material: carbon steel, stainless steel Application: it is used in the occasion where negative pressure suction must be made. Features: the design parameters are based on the experimental theory of all ...
Ultimate vacuum: -800 mbar - 0 mbar
Flow rate: 13, 25 l/min
Operating temperature: 0 °C - 60 °C
... on the Venturi principle. Compressed air enters the ejector and flows through a nozzle. This results in a vacuum immediately behind the nozzle outlet, and air is drawn in through the vacuum inlet. This ...
The Venturi tube, also known as the Venturi tube, is primarily responsible for inducing secondary airflow. When the filter bag is cleaned, when the high-speed airflow passes through the venturi, ...
Sizes: DN 20 to DN 100 Materials: Our jet pumps are made of austenitic stainless steel Standard materials (according to AISI): 316Ti and 321 Materials such as 316L or duplex are also possible upon customer request ...
ZH15D Series Pneumtaic Vacuum Ejector Zh05DS series Vacuum Generator:Fast piping plug and play,Resin material, light weight / long life,Wide application, strong usability.... Product Description ZH05DS ...
In-line ejectors, CIL series With the CIL series, COVAL introduces a new range of “just-plug-it-in” vacuum modules. The in-line CIL vacuum modules are mounted directly in the compressed air network, very close to the ...
Flow rate: 600 m³/h
... transfomed into pressure until it reaches the discharge pressure (C). Ejectors are static devices with no moving part which means a long service life and minimum maintenance. These ejectors are based ...
Please specify:
Help us improve:
remaining