LATTY seals
... the shaft of the o-ring seal for the smooth, low-torque operation usually found only in expensive motion feedthroughs Bronze bushings support the shaft on the 3/8" and 1/2" shaft versions A pre-loaded fluorocarbon o-ring ...
Sealing profileElastic element or the waterproof fastening and closure of flat elements in profile groove.
Temperature limit: -20 °F - 170 °F
... shop. Urethane testing seals are typically supplied in a 60-95A durometer. Urethane seals will match the profile of the piece they are sealing against and typically have a step or lip for the sealing ...
... Bag Loading/Unloading Inflatable Seal Drum Filling Inflatable Seal Airframe Component Bonding Bladder Large Diameter Pool Gate Seals for Nuclear Power Reactors With over 70 standard profiles ...
Pawling Engineered Products, Inc.
Temperature limit: 300 °C
Material: EPDM Gasket height: 11 mm Gasket length: 26 mm Hardness: 65-80 ShA Flash point: above 300 degrees C Recovery capacity at 20 ° C >= 80% Relaxation from compression: 3 months at 70 ° C ≤ 45
Fama S.p.A
Diameter: 20, 22, 24 mm
- Using for classic type pressure cookers.- Available rubber and silicone material. - Available 20 cm – 22 cm – 24 cm dimension.
Casta-sil
TB FM01 for Fristam Pump TB FM01 for Fristam Pump dimension: 30mm Material:SS/Viton ... TB FM01 for Fristam Pump dimension: 30mm Material:SS/Viton
Shanghai Trisun Parts Manufacture Co., Ltd.
... manufactures a wide variety of components, which includes static seals. The static seals are available in four models such as unsplit, split, envelopes and as well as O-rings. A static seal ...
PTFE Competence Center GmbH
At Laygo, we are dedicated to produce the best plate heat exchanger gaskets in the market. We pride ourselves with being the high quality alternative to your regular OEM gaskets and, since 1982, know ...
Laygo Gaskets
Diameter: 0 mm - 2,400 mm
... static seals including lip seals, scrapers, bearing seals and mechanical seals. These include O-rings, elastomer and metal energiser composite seals, ...
REPACK-S
Temperature limit: 982 °C
High temperature filler material for spiral wound gaskets Cryogenics to 1800F / 982C Class 150 to 2500
Flexitallic
... as the height of inflation ("stroke" of the seal) and the centerline bend radius that the seal can negotiate. These performance parameters are further impacted by the cross-section geometry of the seal. ...
SEAL MASTER
The new GARAG’ÉTANCH® FLOOR SEAL ensures a perfect seal between the ground and the door. No Drilling, No Screws Water and Air Sealing Quick and Easy Fit Economical
WATTELEZ
... (FIP) and CURE-IN-PLACE (CIP) Gaskets DYMAX form-in-place (FIP)/cure-in-place (CIP) gaskets cure completely in seconds - even to 1/4 inch thick beads - with good compression set. UV/Visible light curing, ...
DYMAX Europe GmbH
Temperature limit: 0 °C - 1,000 °C
Diameter: 34 mm - 338 mm
HiTemp NovaMica Exhaust Gasket (1000 °C) Material Caracteristics: • Refined Phlogopit-Glimmer with an inlay of stainless steel mesh (316) • typical applications: High thermal and mechanical strains, i.e. exhaust-ducts, ...
STAHLCON GmbH
Diameter: 22 mm
Unit - Each - Qty. Rounding - 10 - Long description - Bonded seals TT/TM - Technical information - The Multiseal centres itself well. Multiseal type SC has an extra inside centring flange, the diameter of ...
Temperature limit: -60 °C - 180 °C
Diameter: 1.6 mm - 4.8 mm
1200 Metal knit EMI/RFI gasket Knitted wire mesh EMI/RFI shielding gasket is a Universal EMC gaskets to shield lower frequencies Highly effective EMI/RFI shielding dust & fluid seal ...
Holland Shielding Systems BV
UGA Rubber Press Seals offers the safest solution for any type of cable linings through walls or ceilings. The press seals can be safely inserted into most of the varied pipe linings, diamond tipped ...
Concrete pipe gakets are produced in either EPDM or SBR. Concerete Pipe can be produced in desired hardness from 45 to 70 Shore A. They have the highest lovel of Ozone durability.
Pirlant Rubber Co
... pre-cut and bulk gasket material. The low precision silicone gaskets are sufficient for typical PEM fuel cell research. The thickness tolerance is +/- 2 mils, so proper thickness selection is critical. ...
ElectroChem
Temperature limit: -40 °C - 200 °C
TRISIL uses all types of TRIMET or TRICAT combined with a sponge or compact elastomer gasket made of silicone, polychloroprene or polyurethane by bonding. They can be used in lengths or in shapes. In this case, some ...
JACQUES DUBOIS
Temperature limit: -30 °C - 100 °C
Diameter: 9 mm - 32 mm
Multi-hole sealing ring, metric • Material: TPE (Thermoplastic elastomer) • Colour: Black • Operating temperature: -30°C ÷ 100°C
Berardi Bullonerie srl
Diameter: 29 mm
The water path leading to the nozzle orifice has been completely redesigned to reduce energy losses caused by turbulence, all sharp cross section changes have been eliminated resulting in a significant increase in water velocity at the ...
Parker Hannifin France SAS
... a variety of markets including fluidpower, aerospace, automotive, oil and gas, life sciences and renewable energies. PTFE seals are suitable for use in harsh environments with températures ranging from cryogénie to 300 ...
Parker Hannifin France SAS
O-rings are circular sealing elements with circular cross-sections, and are mainly used in static applications. The sizes are specified by the inside diameter and the cross section diameter. Our O-rings are manufactured according to metric ...
Parker Hannifin France SAS
Temperature limit: -60 °F - 450 °F
Outer diameter: 0.24, 0.312, 0.307, 0.297, 0.472 in
With #10-32 threads, these EPDM gaskets are designed for applications that require EPDM for chemical compatibility or low temperature. They should not be used in applications with petroleum-based lubricants. Their ...
Your suggestions for improvement:
Receive updates on this section every two weeks.
Please refer to our Privacy Policy for details on how DirectIndustry processes your personal data.
- Brand list
- Manufacturer account
- Buyer account
- Our services
- Newsletter subscription
- About VirtualExpo Group
Please specify:
Help us improve:
remaining