{{product.productLabel}} {{product.model}}
{{#if product.featureValues}}{{product.productPrice.formattedPrice}} {{#if product.productPrice.priceType === "PRICE_RANGE" }} - {{product.productPrice.formattedPriceMax}} {{/if}}
{{#each product.specData:i}}
{{name}}: {{value}}
{{#i!=(product.specData.length-1)}}
{{/end}}
{{/each}}
{{{product.idpText}}}
{{product.productLabel}} {{product.model}}
{{#if product.featureValues}}{{product.productPrice.formattedPrice}} {{#if product.productPrice.priceType === "PRICE_RANGE" }} - {{product.productPrice.formattedPriceMax}} {{/if}}
{{#each product.specData:i}}
{{name}}: {{value}}
{{#i!=(product.specData.length-1)}}
{{/end}}
{{/each}}
{{{product.idpText}}}
ZE-2AI is an I/O module with 2 analog inputs for slave communication over Modbus TCP-IP (Ethernet) and Modbus RTU. The module has server functionality for the 100 Mbit/s Ethernet communication port with Modbus TCP-IP ...
SENECA | Automation Interfaces
... Micro USB on the side RJ45 Programming - DIP Switch (default settings reset) Web Server EASY SETUP Serial ports - Nr.1 RS232/RS485 Nr.1 RS485 Speed - Up to 115.200 bps Supported protocols ...
SENECA | Automation Interfaces
... input // RS485 circuits assures the integrity of your datas. Power supply: - 10..40 Vdc; 19..28 Vac Operating mode: - I/O conversion with PID, I/P conversion without PID, manual (fixedoutput) Input: - Voltage, ...
SENECA | Automation Interfaces
... SWITCH, RELAIS etc.) with all of control systems which are able to communicate by the protocol MODBUS RTU through the RS485 serial interface. A 16 bit counter is available on each input, the maximum frequency input is ...
SENECA | Automation Interfaces
The Z-D-OUT (hw.1with micro USB port on the front panel) is used to drive N.5 SPST relays from all of the control systems which are able to communicate with the transmission protocol MODBUS RTU through the RS485 serial ...
SENECA | Automation Interfaces
... C) and configuration flexibility. Z-5DI-2DO supports RS485 serial communication with Modbus RTU protocol, up to 64 nodes without repeater up to 115 kbps. The power supply wiring and serial connection ...
SENECA | Automation Interfaces
Z-10-D-IN is a module with 10 digital inputs, 16 Vdc self-powered common negative and removable terminals section 2.5 mm. Unlike Rev. Hw1, this module includes 10 inputs with a 32-bit totalizer with a maximum frequency of 2.5 kHz. Among ...
SENECA | Automation Interfaces
... from all of the control systems which are able to communicate with the transmission protocol MODBUS RTU through the RS485 serial interface. The digital output max load is 0,5 A (inductive) and 0,5 A (resistive) with ...
SENECA | Automation Interfaces
ZC-24DI is used to interface N.24 digital signals (PUSH BUTTON, LIMIT SWITCH, REMOTE, CONTROL SWITCH, RELAIS etc.) with all of control systems which are able to communicate by the protocols CANopen or ModBUS RTU (protocol selectable through ...
SENECA | Automation Interfaces
ZC-24DO is used to drive N.24 MOSFETS from all of the control systems which are able to communicate by the protocols CANopen or ModBUS RTU (protocol selectable through dip-switch). The digital output max load is 0,5 Awith ON/OFF delay ...
SENECA | Automation Interfaces
Please specify:
Help us improve:
remaining